Delco 32 volt console

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Delco 32 volt console

BrendaAnnD
Phorum Expert

Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington

#14

07-22-2013, 01:51 AM

Three 12V motorcycle or SLA batteries would work just fine. Yeah, it's a bit over 32 volts, but should not bother the tubes. Worst case, buy 2 12V SLA's and 1 6V SLA.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Delco 32 volt console - by Jayce - 07-19-2013, 05:51 PM

RE: Delco 32 volt console - by Electrothaumaturgist - 07-19-2013, 06:48 PM

RE: Delco 32 volt console - by Jayce - 07-19-2013, 09:44 PM

RE: Delco 32 volt console - by Arran - 07-20-2013, 02:01 AM

RE: Delco 32 volt console - by jerryhawthorne - 07-20-2013, 03:18 PM

RE: Delco 32 volt console - by Sean - 07-20-2013, 03:59 PM

RE: Delco 32 volt console - by Jayce - 07-20-2013, 05:09 PM

RE: Delco 32 volt console - by jerryhawthorne - 07-20-2013, 05:36 PM

RE: Delco 32 volt console - by Sean - 07-20-2013, 09:51 PM

RE: Delco 32 volt console - by Jayce - 07-21-2013, 04:48 PM

RE: Delco 32 volt console - by BrendaAnnD - 07-21-2013, 08:57 PM

RE: Delco 32 volt console - by Arran - 07-21-2013, 10:13 PM

RE: Delco 32 volt console - by codefox1 - 07-21-2013, 11:57 PM

RE: Delco 32 volt console - by BrendaAnnD - 07-22-2013, 01:51 AM

RE: Delco 32 volt console - by Jayce - 07-22-2013, 04:03 PM

RE: Delco 32 volt console - by Jayce - 09-23-2013, 09:50 PM

RE: Delco 32 volt console - by TA Forbes - 09-23-2013, 10:08 PM

RE: Delco 32 volt console - by BrendaAnnD - 09-23-2013, 11:26 PM

RE: Delco 32 volt console - by Arran - 09-24-2013, 12:51 AM

RE: Delco 32 volt console - by TA Forbes - 09-24-2013, 02:02 PM

RE: Delco 32 volt console - by marty - 09-24-2013, 02:20 PM

RE: Delco 32 volt console - by Jayce - 09-24-2013, 04:26 PM

RE: Delco 32 volt console - by marty - 09-24-2013, 05:07 PM

RE: Delco 32 volt console - by TA Forbes - 09-24-2013, 06:26 PM

RE: Delco 32 volt console - by Jayce - 09-24-2013, 07:56 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4752 online users. [Complete List]
» 2 Member(s) | 4750 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me