38-3 Dial question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-3 Dial question

gary rabbitt
Senior Member

Posts: 271
Threads: 12
Joined: Nov 2005
City: Nashville, TN

02-19-2008, 02:57 PM

Hi,
I will have a look and see where that is. I tried to not move anything and mark it all when I took it off.

All it needs is a 1/8" clearance.
Last night I rotated the dial and it only touched slightly. I installed a thin piece of flannel (felt was too thick) on both sides, just in case it touched again. I may be good to go.
I'll have a look at that adjustment later on today. Going to test the trans today , I think it may be ok. Then, on to the recap (restuff of course Icon_smile

)

Take care,
Gary.

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-3 Dial question - by gary rabbitt - 02-18-2008, 04:34 PM

[No subject] - by Ron Ramirez - 02-18-2008, 07:33 PM

[No subject] - by gary rabbitt - 02-18-2008, 08:15 PM

[No subject] - by BDM - 02-19-2008, 01:54 AM

[No subject] - by gary rabbitt - 02-19-2008, 02:57 PM

[No subject] - by planigan - 02-20-2008, 12:53 AM

[No subject] - by gary rabbitt - 02-21-2008, 03:02 AM

[No subject] - by planigan - 02-21-2008, 02:08 PM

[No subject] - by gary rabbitt - 02-22-2008, 01:33 AM

[No subject] - by planigan - 02-22-2008, 01:13 PM

[No subject] - by gary rabbitt - 02-22-2008, 06:31 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me