1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
47-1230 Refinishing
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#17

07-30-2013, 01:47 PM
When I noticed the change to "brushing lacquer" on the Deft cans I asked a guy in the paint department. He indicated nothing had changed in the consistency of the lacquer but "brushing" was added to the label due to restrictions on VOCs as released by reducing and spraying the product. I use Deft and do reduce it as it is rather thick for spraying direct.
At least that's what the paint guy said!
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »


Messages In This Thread
47-1230 Refinishing - by Warren - 06-22-2013, 11:36 PM
RE: 47-1230 Refinishing - by klondike98 - 06-23-2013, 10:45 AM
RE: 47-1230 Refinishing - by Arran - 06-23-2013, 09:08 PM
RE: 47-1230 Refinishing - by Warren - 06-24-2013, 12:49 PM
RE: 47-1230 Refinishing - by Marsupial - 06-27-2013, 03:07 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 06-27-2013, 11:44 PM
RE: 47-1230 Refinishing - by Arran - 06-28-2013, 02:17 AM
RE: 47-1230 Refinishing - by Warren - 06-28-2013, 02:27 PM
RE: 47-1230 Refinishing - by Steve Davis - 06-28-2013, 03:43 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 06-28-2013, 05:02 PM
RE: 47-1230 Refinishing - by Warren - 06-28-2013, 09:07 PM
RE: 47-1230 Refinishing - by Warren - 07-18-2013, 02:26 PM
RE: 47-1230 Refinishing - by Bob Andersen - 07-18-2013, 05:20 PM
RE: 47-1230 Refinishing - by Warren - 07-18-2013, 08:44 PM
RE: 47-1230 Refinishing - by Warren - 07-30-2013, 12:55 AM
RE: 47-1230 Refinishing - by Arran - 07-30-2013, 10:39 AM
RE: 47-1230 Refinishing - by jerryhawthorne - 07-30-2013, 01:47 PM
RE: 47-1230 Refinishing - by Warren - 07-31-2013, 12:01 AM
RE: 47-1230 Refinishing - by jerryhawthorne - 07-31-2013, 12:11 AM
RE: 47-1230 Refinishing - by Warren - 08-03-2013, 11:45 PM
RE: 47-1230 Refinishing - by Warren - 10-13-2013, 10:58 PM
RE: 47-1230 Refinishing - by Warren - 12-13-2013, 07:31 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 12-13-2013, 08:00 PM
RE: 47-1230 Refinishing - by Warren - 12-14-2013, 04:16 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 12-14-2013, 05:22 PM
RE: 47-1230 Refinishing - by Warren - 12-15-2013, 02:17 AM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration