Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

47-1230 Refinishing
#19

Warren, just in case you didn't know, Home Depot carries Deft and I also buy the lacquer thinner there as well.
Regards, Jerry

A friend in need is a pest!  Bill Slee ca 1970.


Messages In This Thread
47-1230 Refinishing - by Warren - 06-22-2013, 11:36 PM
RE: 47-1230 Refinishing - by klondike98 - 06-23-2013, 10:45 AM
RE: 47-1230 Refinishing - by Arran - 06-23-2013, 09:08 PM
RE: 47-1230 Refinishing - by Warren - 06-24-2013, 12:49 PM
RE: 47-1230 Refinishing - by Marsupial - 06-27-2013, 03:07 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 06-27-2013, 11:44 PM
RE: 47-1230 Refinishing - by Arran - 06-28-2013, 02:17 AM
RE: 47-1230 Refinishing - by Warren - 06-28-2013, 02:27 PM
RE: 47-1230 Refinishing - by Steve Davis - 06-28-2013, 03:43 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 06-28-2013, 05:02 PM
RE: 47-1230 Refinishing - by Warren - 06-28-2013, 09:07 PM
RE: 47-1230 Refinishing - by Warren - 07-18-2013, 02:26 PM
RE: 47-1230 Refinishing - by Bob Andersen - 07-18-2013, 05:20 PM
RE: 47-1230 Refinishing - by Warren - 07-18-2013, 08:44 PM
RE: 47-1230 Refinishing - by Warren - 07-30-2013, 12:55 AM
RE: 47-1230 Refinishing - by Arran - 07-30-2013, 10:39 AM
RE: 47-1230 Refinishing - by jerryhawthorne - 07-30-2013, 01:47 PM
RE: 47-1230 Refinishing - by Warren - 07-31-2013, 12:01 AM
RE: 47-1230 Refinishing - by jerryhawthorne - 07-31-2013, 12:11 AM
RE: 47-1230 Refinishing - by Warren - 08-03-2013, 11:45 PM
RE: 47-1230 Refinishing - by Warren - 10-13-2013, 10:58 PM
RE: 47-1230 Refinishing - by Warren - 12-13-2013, 07:31 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 12-13-2013, 08:00 PM
RE: 47-1230 Refinishing - by Warren - 12-14-2013, 04:16 PM
RE: 47-1230 Refinishing - by jerryhawthorne - 12-14-2013, 05:22 PM
RE: 47-1230 Refinishing - by Warren - 12-15-2013, 02:17 AM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently no members online.

>