1939 Packard Bell 48E

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

1939 Packard Bell 48E

RoyG
Member

Posts: 53
Threads: 20
Joined: May 2013
City: Portland, OR

08-08-2013, 08:02 PM

Just picked up a Packard Bell 48E (48F chassis). Found a schematic (Rider) on Nostalgia Air. Any ideas where I might find additional info like alignment data? Light spots on top right and lower right of cabinet in picture is glare.

Find

« Next Oldest | Next Newest »

Messages In This Thread

1939 Packard Bell 48E - by RoyG - 08-08-2013, 08:02 PM

RE: 1939 Packard Bell 48E - by Arran - 08-09-2013, 10:29 AM

RE: 1939 Packard Bell 48E - by Phlogiston - 08-09-2013, 10:33 AM

RE: 1939 Packard Bell 48E - by Arran - 08-09-2013, 11:35 AM

RE: 1939 Packard Bell 48E - by Paul Philco322 - 08-15-2013, 09:26 PM

RE: 1939 Packard Bell 48E - by BrendaAnnD - 08-15-2013, 09:47 PM

RE: 1939 Packard Bell 48E - by chris25260880 - 08-15-2013, 10:49 PM

RE: 1939 Packard Bell 48E - by Phlogiston - 08-16-2013, 12:20 AM

RE: 1939 Packard Bell 48E - by BrendaAnnD - 08-16-2013, 02:15 AM

RE: 1939 Packard Bell 48E - by Arran - 08-16-2013, 08:02 PM

RE: 1939 Packard Bell 48E - by Phlogiston - 08-16-2013, 08:40 PM

RE: 1939 Packard Bell 48E - by BrendaAnnD - 08-16-2013, 09:09 PM

RE: 1939 Packard Bell 48E - by Paul Philco322 - 08-16-2013, 11:15 PM

RE: 1939 Packard Bell 48E - by chris25260880 - 08-16-2013, 11:56 PM

RE: 1939 Packard Bell 48E - by Arran - 08-17-2013, 12:12 AM

RE: 1939 Packard Bell 48E - by chris25260880 - 08-17-2013, 11:36 PM

RE: 1939 Packard Bell 48E - by chris25260880 - 08-17-2013, 11:54 PM

RE: 1939 Packard Bell 48E - by Electrothaumaturgist - 08-18-2013, 12:41 AM

RE: 1939 Packard Bell 48E - by Phlogiston - 08-18-2013, 02:31 AM

RE: 1939 Packard Bell 48E - by Paul Philco322 - 08-18-2013, 11:39 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 5337 online users. [Complete List]
» 2 Member(s) | 5335 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me