1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
information required
Guest
Unregistered
 
#7

02-27-2008, 01:24 PM
I did visit this web site many times by looking thru each year but without success. There's a lot of information and was sure to see the model that I have but nothing. I wanted to attach some photos to my message but I'm not really familar to do it. Any help on this side would be appreciated.
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
information required - by Guest - 02-25-2008, 01:25 PM
[No subject] - by gary rabbitt - 02-25-2008, 05:30 PM
[No subject] - by Ron Ramirez - 02-25-2008, 06:43 PM
[No subject] - by Texasrocker - 02-27-2008, 12:03 AM
[No subject] - by Ron Ramirez - 02-27-2008, 07:32 AM
[No subject] - by Guest - 02-27-2008, 01:18 PM
[No subject] - by Guest - 02-27-2008, 01:24 PM
[No subject] - by Ron Ramirez - 02-27-2008, 06:32 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1044 online users. [Complete List]
» 1 Member(s) | 1043 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration