1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-3 That old musty smell..
Warren
Senior Member
****
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
#13

08-16-2013, 10:48 PM
Codefox's suggestion is very close to the way they would get rid of mold, etc from a house. Brush the killer on(Clorox), then after it is dry, coat it with something(Shellac). Sounds like a very good way to me.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-3 That old musty smell.. - by JROZ - 08-15-2013, 11:56 AM
RE: Philco 38-3 That old musty smell.. - by JROZ - 08-15-2013, 02:17 PM
RE: Philco 38-3 That old musty smell.. - by Arran - 08-15-2013, 10:51 PM
RE: Philco 38-3 That old musty smell.. - by Warren - 08-16-2013, 10:48 PM
RE: Philco 38-3 That old musty smell.. - by JROZ - 08-19-2013, 10:22 AM
RE: Philco 38-3 That old musty smell.. - by morzh - 08-24-2013, 10:35 PM



Users browsing this thread: 10 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 5829 online users. [Complete List]
» 2 Member(s) | 5827 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration