1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
BOL and Crystal Phono Cartridges rebuilding lessons.
Syl
Member
***
Posts: 93
Threads: 10
Joined: Jan 2006
#1

03-01-2008, 10:05 PM
I had at one time a complete How-To available elsewhere (now defunct website) and thought this was THE place to host the complete How-To about crystal cartriges rebuilding.

I am also in the process of rebuilding a BOL cartridge (looooong due work) for a verrrrry nice and patient gentleman and thought it might be interesting to some on a How-to, so my offer to Ron for sharing my findings and steps by steps instructions right here. Ron said "go for it" so here I am.

It will most certainly take some time to complete the BOL How-to as I have a busy schedule but I will post the info as it is available.

The first step will be to post the complete How-To for crystal cartridges which will be done in the next few dayz.

Hope this information to be of help to other collectors/restorers.

Syl
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
BOL and Crystal Phono Cartridges rebuilding lessons. - by Syl - 03-01-2008, 10:05 PM
[No subject] - by Chuck Schwark - 03-01-2008, 10:31 PM
[No subject] - by gary rabbitt - 03-02-2008, 12:28 AM
[No subject] - by Ron Ramirez - 03-02-2008, 01:28 AM
[No subject] - by Guest - 03-03-2008, 10:49 AM
[No subject] - by Syl - 03-20-2008, 11:17 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1479 online users. [Complete List]
» 1 Member(s) | 1478 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration