Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My first set: Philco 40-180
#26

The top image is from before I did anything at all (on the left) and after cleanup with Goop and some Howard's (on the right). Both are from roughly the same vantage point and both were lit by a flash.

The bottom image is looking down at the same side panel. You can still see the unevenness in the finish - not really a surprise, but I'm thinking I'd like to smooth this out a bit.

Overall, I'm REALLY impressed and happy with the results so far! Icon_biggrin Icon_eek


Attached Files Image(s)
       


Messages In This Thread
My first set: Philco 40-180 - by EricS - 08-22-2013, 04:03 PM
RE: My first set: Philco 40-180 - by codefox1 - 08-22-2013, 06:19 PM
RE: My first set: Philco 40-180 - by Jamie - 08-22-2013, 07:25 PM
RE: My first set: Philco 40-180 - by EricS - 08-22-2013, 09:13 PM
RE: My first set: Philco 40-180 - by EricS - 08-22-2013, 09:36 PM
RE: My first set: Philco 40-180 - by Arran - 08-23-2013, 12:22 AM
RE: My first set: Philco 40-180 - by EricS - 08-23-2013, 10:10 AM
RE: My first set: Philco 40-180 - by EricS - 08-23-2013, 05:26 PM
RE: My first set: Philco 40-180 - by Jamie - 08-23-2013, 07:18 PM
RE: My first set: Philco 40-180 - by EricS - 08-23-2013, 09:49 PM
RE: My first set: Philco 40-180 - by EricS - 08-24-2013, 05:55 PM
RE: My first set: Philco 40-180 - by EricS - 08-24-2013, 07:56 PM
RE: My first set: Philco 40-180 - by codefox1 - 08-25-2013, 04:03 PM
RE: My first set: Philco 40-180 - by EricS - 08-25-2013, 08:59 PM
RE: My first set: Philco 40-180 - by EricS - 08-26-2013, 01:56 PM
RE: My first set: Philco 40-180 - by EricS - 08-26-2013, 07:09 PM
RE: My first set: Philco 40-180 - by EricS - 08-26-2013, 07:34 PM
RE: My first set: Philco 40-180 - by Jamie - 08-26-2013, 08:12 PM
RE: My first set: Philco 40-180 - by EricS - 08-27-2013, 09:58 AM
RE: My first set: Philco 40-180 - by EricS - 08-29-2013, 11:24 AM
RE: My first set: Philco 40-180 - by EricS - 09-03-2013, 04:41 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3350 online users. [Complete List]
» 2 Member(s) | 3348 Guest(s)
AvatarAvatar

>