1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Model 96 Restoration Info
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#3

08-28-2013, 11:57 PM
Welcome and you have the toughest of skills for most of us, that of cabinet refinishing. Sounds like you will fit in here well. I'm a little far away for some hands on but others who know where all the information is hidden in terms of references will chip in. There are some good videos done on chassis restoration that will guide you and probably some threads here on the Phorum that will document your chassis. DON'T plug it in until some parts have been renewed.
Here is a link to your schematic in case you don't have one.

Regards, Jerry

http://www.nostalgiaair.org/PagesByModel...013902.pdf
A friend in need is a pest!  Bill Slee ca 1970.
(This post was last modified: 08-29-2013, 12:04 AM by jerryhawthorne.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Model 96 Restoration Info - by TN Allen - 08-28-2013, 12:04 PM
RE: Philco Model 96 Restoration Info - by Eric T - 08-28-2013, 08:21 PM
RE: Philco Model 96 Restoration Info - by jerryhawthorne - 08-28-2013, 11:57 PM
RE: Philco Model 96 Restoration Info - by Jamie - 08-29-2013, 05:50 AM
RE: Philco Model 96 Restoration Info - by Jamie - 09-15-2013, 11:52 AM
RE: Philco Model 96 Restoration Info - by sam - 09-15-2013, 12:04 PM
RE: Philco Model 96 Restoration Info - by sam - 01-15-2015, 12:55 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently 3161 online users. [Complete List]
» 1 Member(s) | 3160 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration