FM alignment

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

FM alignment

Eric Adams
Phorum Expert

Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida

#18

08-29-2013, 08:45 PM

I won the auction for the HP 8601A for $125.00. I have a question about the cables needed. I have the BNC to BNC cables to hook up my frequency counter and scope. I also have a cable with BNC to alligator clips that I use for my RF generator but it doesn't have the 50 ohm resistor. Should it have a 50 ohm resistor across it for all RF outputs, my RF generator as well as the sweep generator when used as an RF generator?
I've been reading the manual and watching videos on You Tube and I think I'm getting an idea how to use it. This really is on of the fun parts of this hobby!

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

FM alignment - by Eric Adams - 08-25-2013, 05:10 PM

RE: FM alignment - by Mondial - 08-25-2013, 09:53 PM

RE: FM alignment - by Eric Adams - 08-25-2013, 10:05 PM

RE: FM alignment - by Eric Adams - 08-25-2013, 10:19 PM

RE: FM alignment - by Mondial - 08-25-2013, 10:32 PM

RE: FM alignment - by Eric Adams - 08-25-2013, 10:39 PM

RE: FM alignment - by Mondial - 08-25-2013, 10:52 PM

RE: FM alignment - by codefox1 - 08-25-2013, 11:31 PM

RE: FM alignment - by Eric Adams - 08-26-2013, 01:16 AM

RE: FM alignment - by Eric Adams - 08-27-2013, 09:23 AM

RE: FM alignment - by BrendaAnnD - 08-27-2013, 11:52 AM

RE: FM alignment - by Eric Adams - 08-27-2013, 01:05 PM

RE: FM alignment - by exray - 08-27-2013, 07:08 PM

RE: FM alignment - by Eric Adams - 08-27-2013, 09:01 PM

RE: FM alignment - by exray - 08-27-2013, 09:28 PM

RE: FM alignment - by Mondial - 08-27-2013, 09:39 PM

RE: FM alignment - by Eric Adams - 08-27-2013, 09:53 PM

RE: FM alignment - by Eric Adams - 08-29-2013, 08:45 PM

RE: FM alignment - by Mondial - 08-29-2013, 09:00 PM

RE: FM alignment - by Eric Adams - 08-29-2013, 09:09 PM

RE: FM alignment - by Eric Adams - 09-01-2013, 09:24 PM

RE: FM alignment - by Mondial - 09-01-2013, 10:01 PM

RE: FM alignment - by Eric Adams - 09-02-2013, 12:10 AM

RE: FM alignment - by BrendaAnnD - 09-02-2013, 04:10 AM

RE: FM alignment - by Eric Adams - 09-02-2013, 09:20 AM

RE: FM alignment - by Mondial - 09-02-2013, 01:44 PM

RE: FM alignment - by Eric Adams - 09-02-2013, 06:14 PM

RE: FM alignment - by Mondial - 09-02-2013, 07:24 PM

RE: FM alignment - by Eric Adams - 09-02-2013, 08:08 PM

RE: FM alignment - by Mondial - 09-02-2013, 08:42 PM

RE: FM alignment - by Eric Adams - 09-03-2013, 01:09 AM

RE: FM alignment - by Mondial - 09-03-2013, 11:16 AM

RE: FM alignment - by Eric Adams - 09-03-2013, 11:36 AM

View a Printable Version

Users browsing this thread: 19 Guest(s)

Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM

Who's Online

There are currently 7263 online users. [Complete List]
» 1 Member(s) | 7262 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me