1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Two Questions
BrendaAnnD
Phorum Expert
*****
Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#8

09-01-2013, 03:52 AM
I'm a little confused (a normal state of affairs for me).

I now see you are using a 1C6 (somehow I had in my mind a 1LC6... go figure). Looking up this tube, I am seeing pins 1 and 6 as filament. From there it goes Pin 2 = Plate, Pin 3 = G2 (osc. plate), Pin 4 = G1 (osc. grid), Pin 5 = G3 & G5, Top cap = G4 (signal grid). This is from pin 1 (the first large pin) clockwise.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Two Questions - by marty - 08-25-2013, 10:04 AM
RE: Two Questions - by morzh - 08-25-2013, 11:15 AM
RE: Two Questions - by marty - 08-31-2013, 12:58 PM
RE: Two Questions - by marty - 08-31-2013, 08:41 PM
RE: Two Questions - by morzh - 08-31-2013, 09:51 PM
RE: Two Questions - by Mondial - 08-31-2013, 10:38 PM
RE: Two Questions - by marty - 08-31-2013, 11:25 PM
RE: Two Questions - by BrendaAnnD - 09-01-2013, 03:52 AM
RE: Two Questions - by BrendaAnnD - 09-01-2013, 04:01 AM
RE: Two Questions - by marty - 09-01-2013, 09:36 AM



Users browsing this thread:
[-]
Recent Posts
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM
Part numbers to model cross
Jim, We have this index put together by Dale Cook but I don't think that is quite what you are looking for. The Parts...klondike98 — 09:37 PM
Philco Model 38-7: what caps & resistors do fail typically?
Yep the dim bulb test is OK but I'd definitely replace all those electrolytics before I did it. Since those #47 conden...klondike98 — 09:18 PM
Philco 42-345 Restoration/Repair
The resistor is a 2.2 Meg, it was the last one I hadn't replaced. The broadcast is coming in after replacing it.osanders0311 — 09:09 PM
Philco 42-345 Restoration/Repair
What does the resistor measure? I think it should be 3.3 Meg. If the oscillator coil has continuity and the resistanc...RodB — 09:03 PM
Philco Model 38-7: what caps & resistors do fail typically?
Good idea to check the coils... then I'll get hold of an incadescent light bulb and see what happens when the unit is sw...Musaeum — 08:49 PM
Philco 42-345 Restoration/Repair
I have that same set, ain't too much shortwave I like anyway.....it is a good AM DX set. PaulPaul Philco322 — 08:32 PM

[-]
Who's Online
There are currently 1422 online users. [Complete List]
» 3 Member(s) | 1419 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration