Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Rogers tabletop 7M632 finished
#8

Thanks for the comments... The grill cloth is original and if you look at the first photo you can see where the veneer is missing along the bottom. There was some missing along the top edge and I replaced it and honestly I have to look hard to find where I did the repair
As far as the CFUN is concerned. I also used to listen to it and I still do when it comes in from Vancouver BC. I had to make up the station letters, I used letroset [spelling?] on opaque plastic so the light would glow through. It was a fun project.


Messages In This Thread
Rogers tabletop 7M632 finished - by Dan Walker - 09-03-2013, 11:01 AM
RE: Rogers tabletop 7M632 finished - by Jamie - 09-03-2013, 12:32 PM
RE: Rogers tabletop 7M632 finished - by rworne - 09-03-2013, 02:45 PM
RE: Rogers tabletop 7M632 finished - by radiodocs - 09-03-2013, 07:36 PM
RE: Rogers tabletop 7M632 finished - by TimC - 09-03-2013, 08:44 PM
RE: Rogers tabletop 7M632 finished - by morzh - 09-03-2013, 09:53 PM
RE: Rogers tabletop 7M632 finished - by Dan Walker - 09-04-2013, 12:36 AM
RE: Rogers tabletop 7M632 finished - by exray - 09-04-2013, 08:34 PM
RE: Rogers tabletop 7M632 finished - by morzh - 09-09-2013, 10:30 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4867 online users. [Complete List]
» 1 Member(s) | 4866 Guest(s)
Avatar

>