1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
40-190 chipped veneer
Arran
Phorum Expert
*****
Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#13

09-06-2013, 01:27 AM
It looks like quarter saw French walnut veneer to me, but cut on the diagonal, you should be able to find a chunk of the same type of veneer that closely matches the grain and colour, it won't be exact but probably good enough. I think you could probably cut a straight sided patch with the sides parallel to the grain.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
40-190 chipped veneer - by fossilexpress - 09-02-2013, 10:07 PM
RE: 40-190 chipped veneer - by Jamie - 09-03-2013, 08:08 AM
RE: 40-190 chipped veneer - by fossilexpress - 09-03-2013, 12:33 PM
RE: 40-190 chipped veneer - by Jamie - 09-03-2013, 01:31 PM
RE: 40-190 chipped veneer - by EricS - 09-03-2013, 02:04 PM
RE: 40-190 chipped veneer - by Arran - 09-03-2013, 10:11 PM
RE: 40-190 chipped veneer - by fossilexpress - 09-03-2013, 10:18 PM
RE: 40-190 chipped veneer - by codefox1 - 09-04-2013, 12:00 PM
RE: 40-190 chipped veneer - by Jamie - 09-05-2013, 11:56 AM
RE: 40-190 chipped veneer - by fossilexpress - 09-05-2013, 08:31 PM
RE: 40-190 chipped veneer - by EricS - 09-05-2013, 11:14 PM
RE: 40-190 chipped veneer - by fossilexpress - 09-05-2013, 11:36 PM
RE: 40-190 chipped veneer - by Arran - 09-06-2013, 01:27 AM
RE: 40-190 chipped veneer - by fossilexpress - 09-15-2013, 11:42 PM
RE: 40-190 chipped veneer - by Jamie - 09-16-2013, 07:10 AM
RE: 40-190 chipped veneer - by EricS - 09-16-2013, 09:51 PM
RE: 40-190 chipped veneer - by EricS - 09-18-2013, 09:22 PM
RE: 40-190 chipped veneer - by fossilexpress - 09-19-2013, 12:29 AM
RE: 40-190 chipped veneer - by EricS - 09-19-2013, 07:18 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 3464 online users. [Complete List]
» 2 Member(s) | 3462 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration