1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
The Philco 17 "Mutt" Lives!
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#11

09-07-2013, 03:47 PM
Interesting!! I think I might have posted that my set been refinished with poly and a very bad job!!! It's over at the shop (where I work when I'm not doing home service) waiting for me to get some free time. The cabinet is apart which makes it pretty wobbly to strip. Front panel and speaker board are out. Was able to get the phrount panel looking good with out damaging the foto phinish Have gotten about 70 percent of the poly off but it is tough stuff!!!
Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
The Philco 17 "Mutt" Lives! - by Jayce - 09-06-2013, 01:04 PM
RE: The Philco 17 "Mutt" - by Ron Ramirez - 09-06-2013, 02:12 PM
RE: The Philco 17 "Mutt" - by Jamie - 09-06-2013, 02:40 PM
RE: The Philco 17 "Mutt" - by marty - 09-06-2013, 02:49 PM
RE: The Philco 17 "Mutt" - by Ron Ramirez - 09-06-2013, 02:54 PM
RE: The Philco 17 "Mutt" - by marty - 09-06-2013, 03:17 PM
RE: The Philco 17 "Mutt" - by Jayce - 09-06-2013, 03:21 PM
RE: The Philco 17 "Mutt" - by Radioroslyn - 09-07-2013, 07:27 AM
RE: The Philco 17 "Mutt" - by Ron Ramirez - 09-07-2013, 08:11 AM
RE: The Philco 17 "Mutt" - by Radioroslyn - 09-07-2013, 03:47 PM
RE: The Philco 17 "Mutt" - by TA Forbes - 09-07-2013, 06:12 PM
RE: The Philco 17 "Mutt" - by Ron Ramirez - 09-07-2013, 08:12 PM
RE: The Philco 17 "Mutt" - by TA Forbes - 09-08-2013, 10:42 AM
RE: The Philco 17 "Mutt" - by Jayce - 09-09-2013, 04:11 PM
RE: The Philco 17 "Mutt" - by Ron Ramirez - 09-09-2013, 04:36 PM
RE: The Philco 17 "Mutt" Lives! - by Jayce - 10-01-2013, 01:12 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5878 online users. [Complete List]
» 2 Member(s) | 5876 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios