1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Oscillator coil
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#6

09-10-2013, 06:58 PM
Rewind the old one. It's simple and cheap. Just need some fine magnet wire. The part that is bad is the small winding near the bottom of the coil. Remove it and replace it with 25 turns magnet wire. Original was 38 gauge but isn't very critical. But the direction is must be wound in the same direction.
Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Oscillator coil - by Philcokid - 09-10-2013, 02:43 PM
RE: Oscillator coil - by Phlogiston - 09-10-2013, 02:52 PM
RE: Oscillator coil - by Philcokid - 09-10-2013, 02:56 PM
RE: Oscillator coil - by morzh - 09-10-2013, 04:32 PM
RE: Oscillator coil - by jerryhawthorne - 09-10-2013, 04:58 PM
RE: Oscillator coil - by Radioroslyn - 09-10-2013, 06:58 PM
RE: Oscillator coil - by codefox1 - 09-10-2013, 07:37 PM
RE: Oscillator coil - by Philcokid - 09-10-2013, 07:43 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM
Philco 60 Squealing
Your IF transformers are tuned to the resonant frequency they were designed for. When you observe the bell curve they di...RodB — 01:35 PM
identify very thin wire for replacement on 37-640
Thanks so much for your help!  I really could not have gotten this far without the kindness of you and other members.  T...georgetownjohn — 11:50 AM
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM

[-]
Who's Online
There are currently 3384 online users. [Complete List]
» 4 Member(s) | 3380 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration