Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-116 and Zenith 9S-262
#17

I suppose it does make a difference how much rubber wire a person has replaced. I have replaced a lot, but I can remember back in the days that I would feel the strong urge to "just leave it" (a bad idea I got over) or turn the radio into a parts set. And I have taken apart a lot of sub chassis, also not so bad by the time you have a couple dozen under your belt. I wonder how many of them have all the caps replaced except the two in the center of the RF and Antenna section?:

http://www.nostalgiaair.org/PagesByModel...013199.pdf

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/


Messages In This Thread
Philco 37-116 and Zenith 9S-262 - by morzh - 09-07-2013, 02:46 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-07-2013, 04:26 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-07-2013, 04:56 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-07-2013, 04:56 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-11-2013, 11:59 AM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-13-2013, 03:14 PM
RE: Philco 37-116 and Zenith 9S-262 - by Phlogiston - 09-13-2013, 09:15 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-14-2013, 05:03 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-15-2013, 04:59 PM
RE: Philco 37-116 and Zenith 9S-262 - by morzh - 09-21-2013, 07:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
[split] New member...
You may have to start further back with your signal injection at the IF signal grid, then tune the second IF transformer...RodB — 10:28 AM
[split] New member...
Well, with the replacement tuning assembly, I have finally put the unit back together and aligned the dial.  The first s...HowardWoodard — 01:01 AM
Philco Model 16 wiring question
Well, finding a short is easy. Like I said, disconnect the transformer's secondary windings and see if it persists. If...morzh — 09:48 PM
Restoring Philco 96
Nice one!Stan the Man — 09:37 PM
Restoring Philco 96
I have eventually replaced the speaker and shot the video, which only shows the upper part of the dial as the hum is ver...morzh — 09:24 PM
Rogers Majestic R-646
Kinda weird to see both open Nothing weird if you remember that this radio is about 100 years old  :)Vlad95 — 07:49 PM
Philco 42-345 Restoration/Repair
I believe I'm making progress, resistors have been rechecked and corrected, removed that ugly blue capacitor and more wi...osanders0311 — 07:38 PM
Philco Model 16 wiring question
Thanks Morzh Yes I recapped everything and replaced almost all the resistors as well. I redid #99 with .015 safety ca...bobclausen — 07:11 PM
Philco Model 16 wiring question
Well...pull out every single load of the transformer. For every winding. Unsolder if needed. Then re-do your dim bulb....morzh — 07:02 PM
Rogers Majestic R-646
Kinda weird to see both open, but once you get it up and running, really pay attention to your sound. Listen for loud cr...TV MAN — 06:59 PM

[-]
Who's Online
There are currently 1018 online users. [Complete List]
» 3 Member(s) | 1015 Guest(s)
AvatarAvatarAvatar

>