1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
They said it couldn't be done...
BrendaAnnD
Phorum Expert
*****
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#11

09-17-2013, 10:26 AM
I'll post this one here, but mostly I'll post in the cabinet restoration thread.

I've opted to forgo the veneer repairs for the time being, deciding instead to sand and restain the cabinet. As you can see from the attached pic, I seem to have missed a few spots with the stain, which I'll take care of tomorrow. To my eye, at least, it's looking a lot better than when it got here.


Attached Files Image(s)
   
Find
« Next Oldest | Next Newest »


Messages In This Thread
They said it couldn't be done... - by BrendaAnnD - 09-13-2013, 08:06 AM
RE: They said it couldn't be done... - by Jamie - 09-13-2013, 08:23 AM
RE: They said it couldn't be done... - by Jamie - 09-13-2013, 05:46 PM
RE: They said it couldn't be done... - by exray - 09-13-2013, 06:24 PM
RE: They said it couldn't be done... - by EricS - 09-17-2013, 09:45 AM
RE: They said it couldn't be done... - by BrendaAnnD - 09-17-2013, 10:26 AM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 6222 online users. [Complete List]
» 2 Member(s) | 6220 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios