1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Need help to ID a Fada
BrendaAnnD
Phorum Expert
*****
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#10

09-24-2013, 12:55 AM
This should be pretty close to your radio. Doubt it's exactly the one.

http://www.nostalgiaair.org/PagesByModel...005651.pdf
Find
« Next Oldest | Next Newest »


Messages In This Thread
Need help to ID a Fada - by Jamie - 09-22-2013, 07:54 PM
RE: Need help to ID a Fada - by morzh - 09-22-2013, 09:20 PM
RE: Need help to ID a Fada - by Arran - 09-22-2013, 10:54 PM
RE: Need help to ID a Fada - by BrendaAnnD - 09-22-2013, 11:19 PM
RE: Need help to ID a Fada - by Jamie - 09-23-2013, 07:55 AM
RE: Need help to ID a Fada - by morzh - 09-23-2013, 06:26 PM
RE: Need help to ID a Fada - by Jamie - 09-23-2013, 08:05 PM
RE: Need help to ID a Fada - by sam - 09-23-2013, 09:59 PM
RE: Need help to ID a Fada - by Arran - 09-24-2013, 12:39 AM
RE: Need help to ID a Fada - by BrendaAnnD - 09-24-2013, 12:55 AM
RE: Need help to ID a Fada - by morzh - 09-24-2013, 10:03 AM
RE: Need help to ID a Fada - by Jamie - 09-24-2013, 10:41 AM
RE: Need help to ID a Fada - by Arran - 09-26-2013, 01:00 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5560 online users. [Complete List]
» 1 Member(s) | 5559 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)