1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
41-95 schematic
brownie45
Member
***
Posts: 54
Threads: 8
Joined: Nov 2012
City: Wilton, Iowa
#5

09-25-2013, 01:32 PM
Try to get a pic & check the model # again.
Was going to recap & check the resistors on the Philco for
sure, & then go into the eliminator to see what that's
like. Have read about those eliminators, but never had
one on the bench.
A thousand pardons---just went out to check the serial
#, & it is 41-95. Had the set out in the shed, & it was
kind of dark. Shows up better out in the sun.
Beitmans still doesn't show this model #.
Thanks. Jim
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
41-95 schematic - by brownie45 - 09-25-2013, 10:30 AM
RE: 41-99 schematic - by marty - 09-25-2013, 11:00 AM
RE: 41-99 schematic - by Carl Travis - 09-25-2013, 11:04 AM
RE: 41-99 schematic - by marty - 09-25-2013, 11:07 AM
RE: 41-99 schematic - by brownie45 - 09-25-2013, 01:32 PM
RE: 41-99 schematic - by BrendaAnnD - 09-25-2013, 03:50 PM
RE: 41-99 schematic - by klondike98 - 09-25-2013, 03:59 PM
RE: 41-99 schematic - by brownie45 - 09-25-2013, 07:12 PM
RE: 41-95 schematic - by brownie45 - 09-26-2013, 01:30 PM
RE: 41-95 schematic - by brownie45 - 11-23-2013, 11:04 AM
RE: 41-95 schematic - by Raleigh - 11-29-2013, 04:52 PM
RE: 41-95 schematic - by brownie45 - 11-30-2013, 07:39 AM
RE: 41-95 schematic - by brownie45 - 12-11-2013, 09:27 PM
RE: 41-95 schematic - by Radioroslyn - 12-11-2013, 11:55 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration