Atwater Kent 328 Early

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater Kent 328 Early

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

09-25-2013, 07:31 PM

I have the covers off and the xformer looks very good with no exposed or bare conductors, insulation looks good and is not flaking and almost as important it smells ok. from looking at the print the shield is between the pri and sec. It was probably there to take static to ground or for noise reduction my guess. I know the new ones do not have them, I will if I have time tomorrow is reinstall and see what happens with the shield disconnected and taped off.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater Kent 328 Early - by Eric - 09-24-2013, 08:09 PM

RE: Atwater Kent 328 Early - by Radioroslyn - 09-24-2013, 09:22 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 11:32 AM

RE: Atwater Kent 328 Early - by Mondial - 09-25-2013, 02:51 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 06:14 PM

RE: Atwater Kent 328 Early - by marty - 09-25-2013, 06:33 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 07:31 PM

RE: Atwater Kent 328 Early - by Arran - 09-25-2013, 10:35 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 11:08 PM

RE: Atwater Kent 328 Early - by Mondial - 09-26-2013, 12:05 AM

RE: Atwater Kent 328 Early - by Arran - 09-26-2013, 12:08 AM

RE: Atwater Kent 328 Early - by Eric - 09-26-2013, 03:18 PM

RE: Atwater Kent 328 Early - by Eric - 10-06-2013, 11:29 AM

RE: Atwater Kent 328 Early - by Mondial - 10-06-2013, 11:51 AM

RE: Atwater Kent 328 Early - by Eric - 10-07-2013, 08:54 PM

RE: Atwater Kent 328 Early - by Eric - 10-08-2013, 06:56 PM

RE: Atwater Kent 328 Early - by Mondial - 10-08-2013, 08:28 PM

RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 11:10 AM

RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 05:15 PM

RE: Atwater Kent 328 Early - by Mondial - 10-09-2013, 06:39 PM

RE: Atwater Kent 328 Early - by Eric - 10-10-2013, 03:28 PM

RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 08:31 AM

RE: Atwater Kent 328 Early - by Eric - 10-11-2013, 08:15 PM

RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 11:16 PM

RE: Atwater Kent 328 Early - by Eric - 10-12-2013, 11:38 AM

RE: Atwater Kent 328 Early - by Mondial - 10-13-2013, 10:31 AM

RE: Atwater Kent 328 Early - by Eric - 10-13-2013, 12:18 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online

There are currently 6506 online users. [Complete List]
» 2 Member(s) | 6504 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me