Atwater Kent 328 Early

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater Kent 328 Early

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

09-25-2013, 11:08 PM

The problem is not in the leads as they are soldered to tabs on the face of the coil and one of the HV leads only measures 24 ohms and the other is 400 ohms to the shield which is the listed resistance of that winding. That tells me that the short is very close to the one lead the question is can I dig into it and clear it, so if I can't repair it I picked 2 Hammond xformers to replace it
1 DX270 Fil1 2a@ 5v, Fil2 3a@ 6.3v and the HVAC 550v CT 104ma
2 DX272 Fil1 3a@ 5v, Fil2 4a@ 6.3v and the HVAC 600v CT 144ma
I have room for the larger is the HVAC voltage ok?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater Kent 328 Early - by Eric - 09-24-2013, 08:09 PM

RE: Atwater Kent 328 Early - by Radioroslyn - 09-24-2013, 09:22 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 11:32 AM

RE: Atwater Kent 328 Early - by Mondial - 09-25-2013, 02:51 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 06:14 PM

RE: Atwater Kent 328 Early - by marty - 09-25-2013, 06:33 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 07:31 PM

RE: Atwater Kent 328 Early - by Arran - 09-25-2013, 10:35 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 11:08 PM

RE: Atwater Kent 328 Early - by Mondial - 09-26-2013, 12:05 AM

RE: Atwater Kent 328 Early - by Arran - 09-26-2013, 12:08 AM

RE: Atwater Kent 328 Early - by Eric - 09-26-2013, 03:18 PM

RE: Atwater Kent 328 Early - by Eric - 10-06-2013, 11:29 AM

RE: Atwater Kent 328 Early - by Mondial - 10-06-2013, 11:51 AM

RE: Atwater Kent 328 Early - by Eric - 10-07-2013, 08:54 PM

RE: Atwater Kent 328 Early - by Eric - 10-08-2013, 06:56 PM

RE: Atwater Kent 328 Early - by Mondial - 10-08-2013, 08:28 PM

RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 11:10 AM

RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 05:15 PM

RE: Atwater Kent 328 Early - by Mondial - 10-09-2013, 06:39 PM

RE: Atwater Kent 328 Early - by Eric - 10-10-2013, 03:28 PM

RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 08:31 AM

RE: Atwater Kent 328 Early - by Eric - 10-11-2013, 08:15 PM

RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 11:16 PM

RE: Atwater Kent 328 Early - by Eric - 10-12-2013, 11:38 AM

RE: Atwater Kent 328 Early - by Mondial - 10-13-2013, 10:31 AM

RE: Atwater Kent 328 Early - by Eric - 10-13-2013, 12:18 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean. Can you explain what you are really saying. If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head. Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640. Does that help?--Johngeorgetownjohn — 02:14 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me