Brought home a fada

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Brought home a fada

Electrothaumaturgist
Senior Member

Posts: 481
Threads: 18
Joined: Jan 2013
City: Mesa, AZ

09-29-2013, 04:58 AM

Hit 'er with PB Blaster at the pivots, let it sit a good while, spray it again, then maybe very lightly rap it with a prod in strategic locations carefully, if possible, put some more PB on 'er and try to work it back and forth. Works most of the time on rusted automobile related parts for me. Heavy duty stuff. That'll be a Deusey of a radio when you're done!!! SWEET!!! Icon_biggrin

(This post was last modified: 09-29-2013, 05:00 AM by Electrothaumaturgist.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Brought home a fada - by jerryhawthorne - 09-28-2013, 10:58 PM

RE: Brought home a fada - by Arran - 09-28-2013, 11:16 PM

RE: Brought home a fada - by jerryhawthorne - 09-29-2013, 02:17 AM

RE: Brought home a fada - by Electrothaumaturgist - 09-29-2013, 04:58 AM

RE: Brought home a fada - by PhilcoJohn - 09-29-2013, 09:02 AM

RE: Brought home a fada - by Jamie - 09-29-2013, 09:24 AM

RE: Brought home a fada - by Jayce - 09-29-2013, 03:32 PM

RE: Brought home a fada - by jerryhawthorne - 09-29-2013, 04:06 PM

RE: Brought home a fada - by Raymanretro - 09-29-2013, 08:45 PM

RE: Brought home a fada - by Arran - 09-30-2013, 02:20 AM

RE: Brought home a fada - by morzh - 09-30-2013, 11:20 AM

RE: Brought home a fada - by TA Forbes - 09-30-2013, 11:25 AM

RE: Brought home a fada - by jerryhawthorne - 09-30-2013, 02:51 PM

RE: Brought home a fada - by jerryhawthorne - 09-30-2013, 07:41 PM

RE: Brought home a fada - by jerryhawthorne - 10-02-2013, 12:11 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM

Who's Online

There are currently 4040 online users. [Complete List]
» 2 Member(s) | 4038 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me