1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
42-1010 Question
PhilcoPhil
Junior Member
**
Posts: 33
Threads: 8
Joined: Nov 2007
#7

03-30-2008, 08:34 PM
Nice pics...I wish they still made radios this way, or anything for that matter. Good Luck with it!!!
Find
« Next Oldest | Next Newest »


Messages In This Thread
42-1010 Question - by TonyJSenior - 03-27-2008, 11:46 AM
[No subject] - by 49Stude63 - 03-27-2008, 03:07 PM
[No subject] - by Ron Ramirez - 03-27-2008, 05:48 PM
[No subject] - by TonyJSenior - 03-30-2008, 07:59 PM
[No subject] - by Ron Ramirez - 03-30-2008, 08:03 PM
[No subject] - by TonyJSenior - 03-30-2008, 08:32 PM
[No subject] - by PhilcoPhil - 03-30-2008, 08:34 PM
[No subject] - by 49Stude63 - 03-31-2008, 02:08 PM
[No subject] - by TonyJSenior - 03-31-2008, 03:22 PM
[No subject] - by 49Stude63 - 03-31-2008, 04:52 PM
[No subject] - by Ron Ramirez - 03-31-2008, 06:43 PM
[No subject] - by 49Stude63 - 03-31-2008, 06:53 PM
[No subject] - by TonyJSenior - 03-31-2008, 08:55 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3909 online users. [Complete List]
» 1 Member(s) | 3908 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration