1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
42-1010 Question
TonyJSenior
Member
***
Posts: 111
Threads: 27
Joined: Oct 2007
City: Livonia, MI
#9

03-31-2008, 03:22 PM
While this may be the case in looking at the picture of my unit vs. the one at Radio Attic, the labels on that unit are above the corresponding button, while mine are incorporated in the center of the button. Possibly this faceplate and buttons were from another radio altogether? I haven't pulled the chassis out and probably won't for awhile, but it sure doesn't appear that too much has been done to the unit.
Find
« Next Oldest | Next Newest »


Messages In This Thread
42-1010 Question - by TonyJSenior - 03-27-2008, 11:46 AM
[No subject] - by 49Stude63 - 03-27-2008, 03:07 PM
[No subject] - by Ron Ramirez - 03-27-2008, 05:48 PM
[No subject] - by TonyJSenior - 03-30-2008, 07:59 PM
[No subject] - by Ron Ramirez - 03-30-2008, 08:03 PM
[No subject] - by TonyJSenior - 03-30-2008, 08:32 PM
[No subject] - by PhilcoPhil - 03-30-2008, 08:34 PM
[No subject] - by 49Stude63 - 03-31-2008, 02:08 PM
[No subject] - by TonyJSenior - 03-31-2008, 03:22 PM
[No subject] - by 49Stude63 - 03-31-2008, 04:52 PM
[No subject] - by Ron Ramirez - 03-31-2008, 06:43 PM
[No subject] - by 49Stude63 - 03-31-2008, 06:53 PM
[No subject] - by TonyJSenior - 03-31-2008, 08:55 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration