Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stewart-Warner 950 battery set
#14

Well, the radio is essentially finished. I could not remove the third transformer from it's can. Of course, after getting molten tar all over my fingers, I also sort of lost the will to fight it anymore. I mounted my replacement transformer on top of the chassis. I also mounted a single solder lug on which to connect my feedback loop. It works pretty well now. Still need to get the proper tube in there so that there's a balance between the two outputs.

By the way.. you know those pain charts you see in the doctor's office? The ones with the faces numbered 1 to 10? Well, in case there are some of you out there that have yet to experience it (and I don't recommend it), having your fingers coated in molten tar is about a 15.. with a screaming face..Icon_eekIcon_eek


Messages In This Thread
Stewart-Warner 950 battery set - by BrendaAnnD - 09-30-2013, 10:34 PM
RE: Stewart-Warner 950 battery set - by Jayce - 09-30-2013, 11:17 PM
RE: Stewart-Warner 950 battery set - by Jayce - 10-01-2013, 10:35 AM
RE: Stewart-Warner 950 battery set - by Arran - 10-01-2013, 10:24 PM
RE: Stewart-Warner 950 battery set - by marty - 10-02-2013, 09:30 AM
RE: Stewart-Warner 950 battery set - by sam - 10-04-2013, 10:57 AM
RE: Stewart-Warner 950 battery set - by Arran - 10-05-2013, 04:29 AM
RE: Stewart-Warner 950 battery set - by BrendaAnnD - 10-05-2013, 04:41 AM
RE: Stewart-Warner 950 battery set - by Arran - 10-05-2013, 07:55 AM
RE: Stewart-Warner 950 battery set - by marty - 10-05-2013, 09:49 AM
RE: Stewart-Warner 950 battery set - by Arran - 10-06-2013, 02:45 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2958 online users. [Complete List]
» 3 Member(s) | 2955 Guest(s)
AvatarAvatarAvatar

>