Atwater Kent 328 Early

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater Kent 328 Early

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#13

10-06-2013, 11:29 AM

Now that the power issues appear to be taken care of I need to start troubleshooting. All caps have been changed except mica ones. First questions
1) I located all resistors and checked for value and changed those over 20% but #7 10k is not there just a jumper on the #4 pins on the 6k7 1st & 2nd IF. Should I install one?
2) Socket markings? What are they?
P-Plate
F-Filament "Heater"
G-grid?
S-screen?
C-cathode
SL-?
CS-?
OP-? 6A8
OG-? 6A8

Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater Kent 328 Early - by Eric - 09-24-2013, 08:09 PM

RE: Atwater Kent 328 Early - by Radioroslyn - 09-24-2013, 09:22 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 11:32 AM

RE: Atwater Kent 328 Early - by Mondial - 09-25-2013, 02:51 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 06:14 PM

RE: Atwater Kent 328 Early - by marty - 09-25-2013, 06:33 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 07:31 PM

RE: Atwater Kent 328 Early - by Arran - 09-25-2013, 10:35 PM

RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 11:08 PM

RE: Atwater Kent 328 Early - by Mondial - 09-26-2013, 12:05 AM

RE: Atwater Kent 328 Early - by Arran - 09-26-2013, 12:08 AM

RE: Atwater Kent 328 Early - by Eric - 09-26-2013, 03:18 PM

RE: Atwater Kent 328 Early - by Eric - 10-06-2013, 11:29 AM

RE: Atwater Kent 328 Early - by Mondial - 10-06-2013, 11:51 AM

RE: Atwater Kent 328 Early - by Eric - 10-07-2013, 08:54 PM

RE: Atwater Kent 328 Early - by Eric - 10-08-2013, 06:56 PM

RE: Atwater Kent 328 Early - by Mondial - 10-08-2013, 08:28 PM

RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 11:10 AM

RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 05:15 PM

RE: Atwater Kent 328 Early - by Mondial - 10-09-2013, 06:39 PM

RE: Atwater Kent 328 Early - by Eric - 10-10-2013, 03:28 PM

RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 08:31 AM

RE: Atwater Kent 328 Early - by Eric - 10-11-2013, 08:15 PM

RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 11:16 PM

RE: Atwater Kent 328 Early - by Eric - 10-12-2013, 11:38 AM

RE: Atwater Kent 328 Early - by Mondial - 10-13-2013, 10:31 AM

RE: Atwater Kent 328 Early - by Eric - 10-13-2013, 12:18 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online

There are currently 6466 online users. [Complete List]
» 1 Member(s) | 6465 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me