tube

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

tube

Eric Adams
Phorum Expert

Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida

10-06-2013, 09:54 PM

Ease up exray Icon_smile

, I don't have every tube that I need at hand and If I'm in the middle of a restoration and in need of a tube, I'll go with a substitute. At least until I can order the correct one. Also, I don't like to wait 2 to 3 weeks for a tube, so Bob is not on the top of my list. Try AES. Icon_thumbup

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

tube - by sam - 10-02-2013, 09:06 PM

RE: tube - by morzh - 10-02-2013, 09:15 PM

RE: tube - by Eric Adams - 10-03-2013, 09:21 PM

RE: tube - by klondike98 - 10-04-2013, 11:27 AM

RE: tube - by sam - 10-04-2013, 12:01 PM

RE: tube - by Eric Adams - 10-04-2013, 08:43 PM

RE: tube - by TA Forbes - 10-06-2013, 02:32 PM

RE: tube - by exray - 10-06-2013, 09:28 PM

RE: tube - by Eric Adams - 10-06-2013, 09:54 PM

RE: tube - by sam - 10-06-2013, 10:45 PM

RE: tube - by exray - 10-07-2013, 07:25 AM

RE: tube - by Ron Ramirez - 10-07-2013, 08:59 AM

RE: tube - by Eric Adams - 10-07-2013, 09:29 AM

RE: tube - by Ron Ramirez - 10-07-2013, 09:50 AM

RE: tube - by marty - 10-07-2013, 10:01 AM

RE: tube - by sam - 10-07-2013, 12:54 PM

RE: tube - by Ron Ramirez - 10-07-2013, 01:02 PM

RE: tube - by TA Forbes - 10-07-2013, 04:30 PM

RE: tube - by Eric Adams - 10-07-2013, 04:34 PM

RE: tube - by Jamie - 10-07-2013, 07:15 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me