Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

#13

Not only is Bob slow, last year I was looking to get a signal generator repaired. It was transistorized so I was lost. Bob told me to send it to him and he would take a look at it. Months went by and after countless emails and many excuses from Bob (it's ready to go, I just have to test it one more time. I've been busy. I'll get to it soon, etc). I told him to send it back. After talking to some people who know transistors, I was able to repair it myself.
So, patience may be a virtue, I have no use for Bob.Icon_thumbdown I'll stick with AES. After all, in this case you get what you pay for.

BTW, I found another reliable source for tubes: http://www.radiotubesupply.com/index.html His name is Roy. He's fast and has a good stock. You may want to give him a try.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org



Messages In This Thread
tube - by sam - 10-02-2013, 08:06 PM
RE: tube - by morzh - 10-02-2013, 08:15 PM
RE: tube - by Eric Adams - 10-03-2013, 08:21 PM
RE: tube - by klondike98 - 10-04-2013, 10:27 AM
RE: tube - by sam - 10-04-2013, 11:01 AM
RE: tube - by Eric Adams - 10-04-2013, 07:43 PM
RE: tube - by TA Forbes - 10-06-2013, 01:32 PM
RE: tube - by exray - 10-06-2013, 08:28 PM
RE: tube - by Eric Adams - 10-06-2013, 08:54 PM
RE: tube - by sam - 10-06-2013, 09:45 PM
RE: tube - by exray - 10-07-2013, 06:25 AM
RE: tube - by Ron Ramirez - 10-07-2013, 07:59 AM
RE: tube - by Eric Adams - 10-07-2013, 08:29 AM
RE: tube - by Ron Ramirez - 10-07-2013, 08:50 AM
RE: tube - by marty - 10-07-2013, 09:01 AM
RE: tube - by sam - 10-07-2013, 11:54 AM
RE: tube - by Ron Ramirez - 10-07-2013, 12:02 PM
RE: tube - by TA Forbes - 10-07-2013, 03:30 PM
RE: tube - by Eric Adams - 10-07-2013, 03:34 PM
RE: tube - by Jamie - 10-07-2013, 06:15 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2967 online users. [Complete List]
» 2 Member(s) | 2965 Guest(s)
AvatarAvatar

>