Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Atwater Kent 328 Early
#21

I did have those leads reversed so I changed them now seeing r6 @5v was 3 but climbed to 5, also seeing 4-5v on the 6k7 grid caps is that ok? Also have to clean the vol pot very scratchy but I'm running out of time for today. Tomorrow I will take a full set of readings. Thanks for the help


Messages In This Thread
Atwater Kent 328 Early - by Eric - 09-24-2013, 07:09 PM
RE: Atwater Kent 328 Early - by Radioroslyn - 09-24-2013, 08:22 PM
RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 10:32 AM
RE: Atwater Kent 328 Early - by Mondial - 09-25-2013, 01:51 PM
RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 05:14 PM
RE: Atwater Kent 328 Early - by marty - 09-25-2013, 05:33 PM
RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 06:31 PM
RE: Atwater Kent 328 Early - by Arran - 09-25-2013, 09:35 PM
RE: Atwater Kent 328 Early - by Eric - 09-25-2013, 10:08 PM
RE: Atwater Kent 328 Early - by Mondial - 09-25-2013, 11:05 PM
RE: Atwater Kent 328 Early - by Arran - 09-25-2013, 11:08 PM
RE: Atwater Kent 328 Early - by Eric - 09-26-2013, 02:18 PM
RE: Atwater Kent 328 Early - by Eric - 10-06-2013, 10:29 AM
RE: Atwater Kent 328 Early - by Mondial - 10-06-2013, 10:51 AM
RE: Atwater Kent 328 Early - by Eric - 10-07-2013, 07:54 PM
RE: Atwater Kent 328 Early - by Eric - 10-08-2013, 05:56 PM
RE: Atwater Kent 328 Early - by Mondial - 10-08-2013, 07:28 PM
RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 10:10 AM
RE: Atwater Kent 328 Early - by Eric - 10-09-2013, 04:15 PM
RE: Atwater Kent 328 Early - by Mondial - 10-09-2013, 05:39 PM
RE: Atwater Kent 328 Early - by Eric - 10-10-2013, 02:28 PM
RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 07:31 AM
RE: Atwater Kent 328 Early - by Eric - 10-11-2013, 07:15 PM
RE: Atwater Kent 328 Early - by Mondial - 10-11-2013, 10:16 PM
RE: Atwater Kent 328 Early - by Eric - 10-12-2013, 10:38 AM
RE: Atwater Kent 328 Early - by Mondial - 10-13-2013, 09:31 AM
RE: Atwater Kent 328 Early - by Eric - 10-13-2013, 11:18 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM

[-]
Who's Online
There are currently 1873 online users. [Complete List]
» 3 Member(s) | 1870 Guest(s)
AvatarAvatarAvatar

>