Ballast Tube Question..

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Ballast Tube Question..

Arran
Phorum Expert

Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

10-18-2013, 01:14 AM

Non polarized caps, wire wound resistors, and a diode combined with a wire wound resistor are all ways to go. You will have to allow for the pilot lamp with any design you chose, most ballasts have a tap for a pilot lamp or two pilot lamps.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

Ballast Tube Question.. - by Jamie - 10-17-2013, 07:13 PM

RE: Ballast Tube Question.. - by Joe Rossi - 10-17-2013, 08:09 PM

RE: Ballast Tube Question.. - by TA Forbes - 10-17-2013, 08:56 PM

RE: Ballast Tube Question.. - by Radioroslyn - 10-17-2013, 10:08 PM

RE: Ballast Tube Question.. - by TA Forbes - 10-17-2013, 10:27 PM

RE: Ballast Tube Question.. - by Arran - 10-18-2013, 01:14 AM

RE: Ballast Tube Question.. - by Radioroslyn - 10-18-2013, 07:17 AM

RE: Ballast Tube Question.. - by Jamie - 10-18-2013, 08:17 AM

RE: Ballast Tube Question.. - by BrendaAnnD - 10-18-2013, 09:11 AM

RE: Ballast Tube Question.. - by Mondial - 10-18-2013, 09:42 AM

RE: Ballast Tube Question.. - by Jamie - 10-18-2013, 02:07 PM

RE: Ballast Tube Question.. - by Mondial - 10-18-2013, 06:04 PM

RE: Ballast Tube Question.. - by Arran - 10-18-2013, 10:44 PM

RE: Ballast Tube Question.. - by BrendaAnnD - 10-18-2013, 10:53 PM

RE: Ballast Tube Question.. - by Mondial - 10-18-2013, 11:02 PM

RE: Ballast Tube Question.. - by GarySP - 10-18-2013, 11:25 PM

RE: Ballast Tube Question.. - by Jamie - 10-19-2013, 10:04 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 6035 online users. [Complete List]
» 2 Member(s) | 6033 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me