Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I "stole" a 116B
#14

This set is in your book. I found a totally stripped 116B cabinet at the Findlay, Ohio ham swap one year. No chassis; no nuttin'. It was about 10 bucks, so I bought it. That year, at AWA, John Wolkonowicz knew a guy there who was junking one, on the spot. He took the power trans., and a few other things, so I ended up with the chassis sans a few things that I had on hand at home. A speaker and speaker board were with the cabinet, which was just driftwood. By the time I arrived home, I had enough pieces to completely build a working set. I did assemble all the stuff, finish the cabinet, re-cap, of course, and there it is: a complete 116B. Very soon after, the other 116B came along; possibly again, at AWA. Re-cap and total refinish, and it's also in your book.

Now Ron, you think YOU got a real shlemiel deal? Try this one. I was at the flea market in Pontiac, Mich., one Saturday.I looked beneath a vendor's table, and saw a Philco 16?, 116? from the rear. Looked at it from the front, and it was a 1935 vintage 16B. How much, sez I? Ten bucks, sez he, and 10 clams came ripping out of my wallet like a rocket.

I restored it; both chassis and cabinet. It was a aurplus set to me, so a friend talked me out of it. He was ecstatic over it, of course. One of those rare occasions where I sell anything.


Messages In This Thread
I "stole" a 116B - by Ron Ramirez - 04-03-2008, 11:41 PM
[No subject] - by exray - 04-03-2008, 11:54 PM
[No subject] - by TonyJSenior - 04-04-2008, 11:38 AM
[No subject] - by Alan Douglas - 04-04-2008, 05:05 PM
[No subject] - by BDM - 04-04-2008, 09:04 PM
[No subject] - by Texasrocker - 04-05-2008, 02:05 AM
[No subject] - by Ron Ramirez - 04-05-2008, 10:00 AM
[No subject] - by Alan Douglas - 04-05-2008, 05:08 PM
[No subject] - by Ron Ramirez - 04-05-2008, 07:48 PM
[No subject] - by Alan Douglas - 04-05-2008, 10:06 PM
[No subject] - by Ron Ramirez - 04-05-2008, 11:35 PM
[No subject] - by 49Stude63 - 04-06-2008, 10:39 AM
[No subject] - by Ron Ramirez - 04-07-2008, 07:56 PM
[No subject] - by Doug Houston - 04-07-2008, 09:10 PM
Re: I "stole" a 116B - by n9vu - 04-11-2008, 06:33 AM
Re: I "stole" a 116B - by n9vu - 04-13-2008, 05:20 PM
[No subject] - by Ron Ramirez - 04-13-2008, 06:33 PM
Re: I "stole" a 116B - by Ron Ramirez - 10-12-2008, 10:40 PM
Re: I "stole" a 116B - by BDM - 10-12-2008, 10:45 PM
Re: I "stole" a 116B - by Ron Ramirez - 10-12-2008, 10:51 PM
Re: I "stole" a 116B - by BDM - 10-12-2008, 10:56 PM
Re: I "stole" a 116B - by philcobenz - 10-12-2008, 11:20 PM
Re: I "stole" a 116B - by Ron Ramirez - 10-12-2008, 11:29 PM
Re: I "stole" a 116B - by etech - 10-13-2008, 07:01 AM
Re: I "stole" a 116B - by philcobenz - 10-13-2008, 09:45 AM
Re: I "stole" a 116B - by Ron Ramirez - 10-13-2008, 07:04 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5568 online users. [Complete List]
» 1 Member(s) | 5567 Guest(s)
Avatar

>