Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoring a 39-7
#18

It sings again!

After putting up with the repaired speaker that tended to muddle the sound and distort at medium-high volumes, I decided to take a closer look

The speaker was slowly disintegrating - small cracks were developing, and the most careful light touch caused the cone to split.

So I had the speaker reconed.

It's now a whole different radio. Plays loud, tight, and clear at all volumes.

I probably put more money I to this than I should, but it would have been a pity to leave it in such poor condition.

   


Messages In This Thread
Restoring a 39-7 - by rworne - 08-15-2013, 09:34 AM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 02:18 PM
RE: Restoring a 39-7 - by jerryhawthorne - 08-30-2013, 02:27 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 02:34 PM
RE: Restoring a 39-7 - by BrendaAnnD - 08-30-2013, 04:13 PM
RE: Restoring a 39-7 - by jerryhawthorne - 08-30-2013, 04:22 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 05:05 PM
RE: Restoring a 39-7 - by morzh - 08-30-2013, 05:17 PM
RE: Restoring a 39-7 - by jerryhawthorne - 08-30-2013, 05:29 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 05:52 PM
RE: Restoring a 39-7 - by Arran - 08-30-2013, 09:42 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 11:32 PM
RE: Restoring a 39-7 - by Jamie - 08-31-2013, 01:36 PM
RE: Restoring a 39-7 - by rworne - 08-31-2013, 02:25 PM
RE: Restoring a 39-7 - by hunter2115 - 09-05-2013, 08:31 PM
RE: Restoring a 39-7 - by morzh - 09-05-2013, 08:38 PM
RE: Restoring a 39-7 - by rworne - 09-05-2013, 10:12 PM
RE: Restoring a 39-7 - by rworne - 10-22-2013, 08:49 AM
RE: Restoring a 39-7 - by Mondial - 10-22-2013, 08:54 AM
RE: Restoring a 39-7 - by rworne - 10-22-2013, 09:14 AM
RE: Restoring a 39-7 - by Radioroslyn - 10-22-2013, 04:53 PM
RE: Restoring a 39-7 - by rworne - 10-22-2013, 07:28 PM



Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2881 online users. [Complete List]
» 1 Member(s) | 2880 Guest(s)
Avatar

>