Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 41-280 "slide Rule" dial
#7

Sounds like it's going pretty good. I'll need top order the same strip from Rock Sea, so I'll need to check carefully to make sure I get the right one.

I've discovered an intermittent somewhere in the front end. It'll pass 455 Khz just fine, but that's about it. It would occasionally come back if I jockeyed the bandswitch a little, but now I can only get signal by tapping the heel of the screwdriver in "never the same place".

Obviously, I missed something the first time through, so it's back on the bench. I'll post what I find, hopefully soon.

At least it looks good - I'll post a picture when the film gets developed (hey...I'm old fashioned - no digital camera yet!). Icon_smile

Bill

Sent from my Pentium II on the AT&T Dial Network


Messages In This Thread
Model 41-280 "slide Rule" dial - by bill T - 11-07-2005, 06:50 AM
[No subject] - by Bill Hutchinson - 11-07-2005, 10:31 AM
[No subject] - by bill T - 11-08-2005, 06:50 AM
[No subject] - by bill T - 11-19-2005, 10:43 AM
[No subject] - by Bill Hutchinson - 11-19-2005, 04:35 PM
[No subject] - by bill T - 11-22-2005, 01:52 PM
[No subject] - by Bill Hutchinson - 11-22-2005, 06:58 PM
[No subject] - by bill T - 11-23-2005, 12:07 AM
[No subject] - by Bill Hutchinson - 12-01-2005, 01:50 PM
[No subject] - by bill T - 12-03-2005, 07:01 AM
[No subject] - by Bill Hutchinson - 01-04-2006, 04:52 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>