urges transformer for 765 zenith

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

urges transformer for 765 zenith

BrendaAnnD
Phorum Expert

Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington

10-24-2013, 04:17 PM

BTW, I'll try to remember, if I'm in a thread like this, to post in both English and Spanish as a courtesy to the other Phorum members (and as a quality check for MY translation!)

Find

« Next Oldest | Next Newest »

Messages In This Thread

urges transformer for 765 zenith - by locuspiolin - 10-24-2013, 06:18 AM

RE: urges transformer for 765 zenith - by BrendaAnnD - 10-24-2013, 07:34 AM

RE: urges transformer for 765 zenith - by locuspiolin - 10-24-2013, 08:30 AM

RE: urges transformer for 765 zenith - by BrendaAnnD - 10-24-2013, 11:17 AM

RE: urges transformer for 765 zenith - by Ron Ramirez - 10-24-2013, 02:52 PM

RE: urges transformer for 765 zenith - by BrendaAnnD - 10-24-2013, 04:14 PM

RE: urges transformer for 765 zenith - by BrendaAnnD - 10-24-2013, 04:17 PM

RE: urges transformer for 765 zenith - by TA Forbes - 10-25-2013, 11:12 AM

RE: urges transformer for 765 zenith - by BrendaAnnD - 10-25-2013, 12:29 PM

RE: urges transformer for 765 zenith - by Jamie - 10-25-2013, 12:48 PM

RE: urges transformer for 765 zenith - by morzh - 10-25-2013, 06:08 PM

RE: urges transformer for 765 zenith - by Paul Philco322 - 10-26-2013, 10:48 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old. My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum. Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

Who's Online

There are currently 551 online users. [Complete List]
» 1 Member(s) | 550 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me