Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Rescued an 87 lowboy today.
#2

Hey Jayce
The 87 is a good old set! I think Philco called it their Neutrodyne Plus. Can't remember what the Plus was.
Here's what I did on mine about two years ago. Best I remember I started on Sunday after Church and had it working by 11pm.
http://philcoradio.com/phorum/showthread.php?tid=3490
Rebuilt the filter bank, replaced three or four bypass caps, rewound a couple of the RF coils, replaced some weak 26's, and did the alignment. Play great everyday for about a year then the input cap in the bank shorted. I should have used a mylar but I chose to use some cheap electrolytic jobs. It's been out in the shed for while now.
Terry


Messages In This Thread
Rescued an 87 lowboy today. - by Jayce - 10-25-2013, 08:40 PM
RE: Rescued an 87 lowboy today. - by Radioroslyn - 10-25-2013, 09:51 PM
RE: Rescued an 87 lowboy today. - by Arran - 10-25-2013, 11:16 PM
RE: Rescued an 87 lowboy today. - by Mondial - 10-26-2013, 05:10 PM
RE: Rescued an 87 lowboy today. - by Radioroslyn - 10-26-2013, 08:34 PM
RE: Rescued an 87 lowboy today. - by Arran - 10-26-2013, 09:28 PM
RE: Rescued an 87 lowboy today. - by Jayce - 10-27-2013, 09:04 PM
RE: Rescued an 87 lowboy today. - by Arran - 10-29-2013, 12:36 AM
RE: Rescued an 87 lowboy today. - by TA Forbes - 10-29-2013, 01:49 PM
RE: Rescued an 87 lowboy today. - by Jayce - 10-29-2013, 07:44 PM
RE: Rescued an 87 lowboy today. - by Jayce - 11-11-2013, 10:37 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4683 online users. [Complete List]
» 1 Member(s) | 4682 Guest(s)
Avatar

>