48-1262

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

48-1262

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#10

10-30-2013, 08:15 PM

Well part of your issue is that test point B is where you should be hooking the - lead of your voltmeter. Test point B is the negative side of the power supply. So measure A,C,and D against B and tell me what you get.
The other
Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

48-1262 - by ke5yum - 10-08-2013, 01:14 PM

RE: 48-1262 - by klondike98 - 10-08-2013, 04:05 PM

RE: 48-1262 - by BrendaAnnD - 10-08-2013, 04:09 PM

RE: 48-1262 - by ke5yum - 10-09-2013, 07:42 AM

RE: 48-1262 - by ke5yum - 10-22-2013, 07:56 AM

RE: 48-1262 - by Radioroslyn - 10-22-2013, 06:05 PM

RE: 48-1262 - by Radioroslyn - 10-22-2013, 06:48 PM

RE: 48-1262 - by ke5yum - 10-23-2013, 08:05 AM

RE: 48-1262 - by ke5yum - 10-30-2013, 07:57 AM

RE: 48-1262 - by Radioroslyn - 10-30-2013, 08:15 PM

RE: 48-1262 - by ke5yum - 10-31-2013, 08:02 AM

RE: 48-1262 - by Radioroslyn - 10-31-2013, 04:53 PM

RE: 48-1262 - by ke5yum - 11-01-2013, 07:50 AM

RE: 48-1262 - by ke5yum - 12-13-2013, 09:16 AM

RE: 48-1262 - by Radioroslyn - 12-15-2013, 01:08 PM

RE: 48-1262 - by ke5yum - 12-18-2013, 09:37 AM

RE: 48-1262 - by klondike98 - 12-18-2013, 10:03 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 4252 online users. [Complete List]
» 2 Member(s) | 4250 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me