Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grill cloth philco 40-180
#7

Hi,
So this stuff can probably be found somewhere, make a print of the photos and take it with you to the fabric stores. At least they may know what it's called.

Try to go to as genuine fabric store as Joanns, or Michael's fabric dept. leaves much to be desired.

You might just get a close pattern home dec or upholstery cloth to dye and install. You don't want something really pretty behind there 'cause it will be mostly hidden anyway.

By the way, the cloth I show, could have flaked off much of the fuzziness over the years. I can't remember what the unexposed areas looked like. They might have had more fluff on the threads originally.

Good luck,
Gary.


Messages In This Thread
Grill cloth philco 40-180 - by jerm - 04-15-2008, 02:06 PM
[No subject] - by Chuck Schwark - 04-15-2008, 03:02 PM
[No subject] - by jerm - 04-15-2008, 05:44 PM
RE: Grill cloth philco 40-180 - by BDM - 04-15-2008, 06:22 PM
RE: Grill cloth philco 40-180 - by gary rabbitt - 04-15-2008, 10:06 PM
[No subject] - by jerm - 04-15-2008, 10:51 PM
[No subject] - by gary rabbitt - 04-16-2008, 02:14 PM
[No subject] - by Chuck Schwark - 04-16-2008, 04:50 PM
[No subject] - by gary rabbitt - 04-17-2008, 02:52 PM
[No subject] - by jerm - 04-17-2008, 09:31 PM
RE: Grill cloth philco 40-180 - by gary rabbitt - 04-19-2008, 01:03 AM
[No subject] - by BDM - 04-19-2008, 01:14 AM
[No subject] - by jerm - 04-19-2008, 09:04 AM
[No subject] - by Ron Ramirez - 04-19-2008, 09:30 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>