Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Finally finished my 116
#13

Audiomagnate;

You would have to hear one to be able to appreciate the sound. Suffice to say that it is full-range and comes from a push-pull output stage via a nice 10" speaker. I used to listen to international shortwave broadcasts on one in the late 1950s with a friend. We always were impressed by the quality of the sound from this 20 plus year old set at the time. At one time the high end of the AM broadcast band was set aside for stations to broadcast in higher fidelity with extended high frequency audio content. The better sets could rival some of the better Hi-Fi equipment of the 1950s and 1960s. There are still a few stations that have good audio and programming. Intl. shortwave is still active and some good music programs are presented from time to time.


Messages In This Thread
Finally finished my 116 - by Steve Chambers - 08-24-2013, 05:02 PM
RE: Finally finished my 116 - by Ron Ramirez - 08-24-2013, 05:33 PM
RE: Finally finished my 116 - by Jamie - 08-24-2013, 05:38 PM
RE: Finally finished my 116 - by Eric T - 08-24-2013, 06:28 PM
RE: Finally finished my 116 - by Bill Kinghorn - 08-24-2013, 07:41 PM
RE: Finally finished my 116 - by Paul Philco322 - 08-24-2013, 09:24 PM
RE: Finally finished my 116 - by Gene Pederson - 08-24-2013, 09:42 PM
RE: Finally finished my 116 - by TimC - 08-25-2013, 07:53 PM
RE: Finally finished my 116 - by Ron Ramirez - 08-25-2013, 08:25 PM
RE: Finally finished my 116 - by TimC - 08-25-2013, 08:47 PM
RE: Finally finished my 116 - by EricS - 08-27-2013, 09:04 AM
RE: Finally finished my 116 - by audiomagnate - 08-27-2013, 10:15 AM
RE: Finally finished my 116 - by Joeztech - 11-08-2013, 07:55 PM
RE: Finally finished my 116 - by PhilcoJohn - 11-08-2013, 08:28 PM
RE: Finally finished my 116 - by Jayce - 11-08-2013, 11:50 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently no members online.

>