Stromberg-Carlson 225-H

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Stromberg-Carlson 225-H

morzh
Odobenus rosmarus

Posts: 15,839
Threads: 554
Joined: Oct 2011
City: Jackson, NJ

#16

11-10-2013, 10:32 PM

Boy that ballast tube gets hot....first I thought something was heating and then I realized that that was the ballast and the enamel I used (for gas ranges so it is heat-resistant) gave a little smell. Empty scare but....can never be too careful.

I will tend to the big green dude tomorrow some more, I've done enough today. Some serious voltage measurements plus alignment. I think it is a bit out of it, it behaves very much like the other AA5 out of alignment....or any other radio....

OK, tomorrow then.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Stromberg-Carlson 225-H - by morzh - 09-16-2013, 10:00 PM

RE: Stromberg-Carlson 225-H - by BrendaAnnD - 09-16-2013, 10:22 PM

RE: Stromberg-Carlson 225-H - by Mondial - 09-16-2013, 10:51 PM

RE: Stromberg-Carlson 225-H - by morzh - 09-16-2013, 11:13 PM

RE: Stromberg-Carlson 225-H - by morzh - 09-17-2013, 09:01 PM

RE: Stromberg-Carlson 225-H - by morzh - 10-02-2013, 10:18 PM

RE: Stromberg-Carlson 225-H - by morzh - 10-15-2013, 01:37 PM

RE: Stromberg-Carlson 225-H - by Jamie - 10-15-2013, 07:55 PM

RE: Stromberg-Carlson 225-H - by morzh - 10-15-2013, 09:57 PM

RE: Stromberg-Carlson 225-H - by Jamie - 10-15-2013, 10:07 PM

RE: Stromberg-Carlson 225-H - by morzh - 10-15-2013, 10:12 PM

RE: Stromberg-Carlson 225-H - by Arran - 10-16-2013, 01:12 AM

RE: Stromberg-Carlson 225-H - by morzh - 10-16-2013, 08:39 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-10-2013, 07:54 PM

RE: Stromberg-Carlson 225-H - by Paul Philco322 - 11-10-2013, 09:07 PM

RE: Stromberg-Carlson 225-H - by morzh - 11-10-2013, 10:32 PM

RE: Stromberg-Carlson 225-H - by morzh - 11-11-2013, 11:05 PM

RE: Stromberg-Carlson 225-H - by Arran - 11-12-2013, 12:32 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-12-2013, 01:31 PM

RE: Stromberg-Carlson 225-H - by Arran - 11-13-2013, 02:02 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-17-2013, 11:15 PM

RE: Stromberg-Carlson 225-H - by morzh - 11-21-2013, 11:23 PM

RE: Stromberg-Carlson 225-H - by morzh - 11-23-2013, 10:51 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-23-2013, 10:57 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-23-2013, 11:00 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-23-2013, 11:03 AM

RE: Stromberg-Carlson 225-H - by morzh - 11-23-2013, 11:04 AM

RE: Stromberg-Carlson 225-H - by jerryhawthorne - 11-23-2013, 06:02 PM

RE: Stromberg-Carlson 225-H - by morzh - 11-23-2013, 07:22 PM

RE: Stromberg-Carlson 225-H - by Arran - 11-27-2013, 11:38 PM

RE: Stromberg-Carlson 225-H - by morzh - 11-28-2013, 11:50 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM
38-10T chassis Restoration begins
I have a question about the mica sheets. I thought I saw somewhere on the Phorum where someone used thin plastic report ...dconant — 10:44 AM
38-10T chassis Restoration begins
Yes, you should carefully remove the mica sheets from the trimmers otherwise you risk trapping foreign material in the t...RodB — 10:34 AM
American Bosch Model 802 auto radio
Hi Joe, Thank you again. The American Bosch Model 634A has the same tube lineup as my Model 802 and the parts layout dia...Antipodal — 03:09 AM
38-10T chassis Restoration begins
hello everyone, I know it has been a while since I have posted about this radio but finally got chance work on it . I ...radiorich — 02:45 AM
Rusty Tuning Condenser
You could soak the fins in vinegar. You have to be careful if any pot metal is involved because the vinegar will dissolv...RodB — 09:20 PM
Rusty Tuning Condenser
Hello, I have a Philco 91 where the tuning condenser fins are rusty. I magnet sticks to them so they can't be aluminium....dconant — 05:50 PM

Who's Online

There are currently 2912 online users. [Complete List]
» 1 Member(s) | 2911 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me