1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Pharm Radio Phun !
Chris Cusick
Junior Member
**
Posts: 34
Threads: 7
Joined: Jan 2012
City: Woodstock Illinois
#3

11-14-2013, 05:49 PM
OK - Thanks - I have a little digital AM radio, and using this to pick up the frequency of the LO, I am only getting a small range which coincides with the stations that I can pick up - so nothing at the low end below about 670 kHz (1125 kHz from the LO). I can pick it up for frequencies as high as my digital set will go which equates to 1245 kHz on the Philco, being 1700 kHz in the digital set. Practically I can pick up actual stations between 720 and 1050 kHz although everything is too far up the dial.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Pharm Radio Phun ! - by Chris Cusick - 11-13-2013, 04:31 PM
RE: Pharm Radio Phun ! - by Radioroslyn - 11-13-2013, 09:27 PM
RE: Pharm Radio Phun ! - by Chris Cusick - 11-14-2013, 05:49 PM
RE: Pharm Radio Phun ! - by BrendaAnnD - 11-14-2013, 06:09 PM
RE: Pharm Radio Phun ! - by Mondial - 11-14-2013, 09:18 PM
RE: Pharm Radio Phun ! - by BrendaAnnD - 11-14-2013, 09:58 PM
RE: Pharm Radio Phun ! - by Phlogiston - 11-14-2013, 10:13 PM
RE: Pharm Radio Phun ! - by Mondial - 11-15-2013, 12:16 AM
RE: Pharm Radio Phun ! - by Chris Cusick - 11-15-2013, 11:53 AM
RE: Pharm Radio Phun ! - by BrendaAnnD - 11-15-2013, 04:28 PM
RE: Pharm Radio Phun ! - by Chris Cusick - 11-15-2013, 06:27 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4702 online users. [Complete List]
» 2 Member(s) | 4700 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration