Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 40-201 Speaker
#1

The Philco 40-201 uses a 36-1450 field core speaker. It appears that the DC resistance is 860 ohms and that the current through it is 122ma with a voltage drop of 105 volts. The power dissipation is about 12.8 watts.

What is the impedance of the voice coil? Its DC resistance is not shown on the schematics I have. The OEM speaker is missing so I may need to use a PM replacement until I can get an OEM unit to install. Voice coil impedance may not be much of an issue except for power mismatch if a replacement speaker is way off.

Joe


Messages In This Thread
Philco 40-201 Speaker - by Joeztech - 11-17-2013, 10:17 AM
RE: Philco 40-201 Speaker - by Radioroslyn - 11-18-2013, 09:06 AM
RE: Philco 40-201 Speaker - by Joeztech - 11-18-2013, 03:13 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-18-2013, 06:18 PM
RE: Philco 40-201 Speaker - by BrendaAnnD - 11-18-2013, 08:11 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-18-2013, 08:31 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-19-2013, 06:49 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-20-2013, 07:54 PM
RE: Philco 40-201 Speaker - by Ron Ramirez - 11-20-2013, 08:45 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-20-2013, 08:52 PM
RE: Philco 40-201 Speaker - by Ron Ramirez - 11-20-2013, 09:04 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-21-2013, 07:15 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-21-2013, 07:54 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-23-2013, 02:35 PM
RE: Philco 40-201 Speaker - by Ron Ramirez - 11-26-2013, 06:47 AM
RE: Philco 40-201 Speaker - by Joeztech - 11-26-2013, 07:52 AM
RE: Philco 40-201 Speaker - by Steve D - 11-26-2013, 09:12 AM
RE: Philco 40-201 Speaker - by Mondial - 11-26-2013, 06:49 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-26-2013, 07:20 PM
RE: Philco 40-201 Speaker - by Mondial - 11-26-2013, 08:57 PM
RE: Philco 40-201 Speaker - by Joeztech - 11-26-2013, 09:01 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>