Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Removing Rodent Odor
#11

Another way is to put glue in a straw, flatten the end and put it under the loose veneer and roll the other end to squeeze the glue out.

Steve

M R Radios   C M Tubes


Messages In This Thread
Removing Rodent Odor - by Joeztech - 11-17-2013, 08:42 AM
RE: Removing Rodent Odor - by Phlogiston - 11-17-2013, 12:45 PM
RE: Removing Rodent Odor - by Joeztech - 11-17-2013, 09:28 PM
RE: Removing Rodent Odor - by Joeztech - 11-18-2013, 05:38 PM
RE: Removing Rodent Odor - by Phlogiston - 11-18-2013, 07:44 PM
RE: Removing Rodent Odor - by Joeztech - 11-18-2013, 08:20 PM
RE: Removing Rodent Odor - by Arran - 11-19-2013, 03:43 AM
RE: Removing Rodent Odor - by Joeztech - 11-19-2013, 07:52 AM
RE: Removing Rodent Odor - by klondike98 - 11-19-2013, 10:05 AM
RE: Removing Rodent Odor - by Joeztech - 11-19-2013, 06:28 PM
RE: Removing Rodent Odor - by Steve Davis - 11-19-2013, 06:51 PM
RE: Removing Rodent Odor - by Joeztech - 11-19-2013, 08:47 PM
RE: Removing Rodent Odor - by klondike98 - 11-19-2013, 10:29 PM
RE: Removing Rodent Odor - by tom.seeger - 11-19-2013, 10:31 PM
RE: Removing Rodent Odor - by Joeztech - 11-20-2013, 08:32 AM
RE: Removing Rodent Odor - by Joeztech - 11-20-2013, 07:00 PM
RE: Removing Rodent Odor - by Joeztech - 11-23-2013, 03:05 PM
RE: Removing Rodent Odor - by Joeztech - 11-23-2013, 03:25 PM
RE: Removing Rodent Odor - by Joeztech - 11-28-2013, 06:00 PM
RE: Removing Rodent Odor - by Joeztech - 11-29-2013, 05:59 PM
RE: Removing Rodent Odor - by Ron Ramirez - 11-29-2013, 06:01 PM
RE: Removing Rodent Odor - by Ron Ramirez - 11-29-2013, 06:03 PM
RE: Removing Rodent Odor - by Joeztech - 11-30-2013, 07:51 AM
RE: Removing Rodent Odor - by Ron Ramirez - 11-30-2013, 08:45 AM
RE: Removing Rodent Odor - by Joeztech - 12-01-2013, 06:30 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>