1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 1942 radio
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#2

11-21-2013, 06:13 PM
Shirley, welcome and I'm certain someone in your area can supply a contact for you. These old radios are a wonderful part of family history. You should post the model number which is normally stamped on the back of the chassis or on a sticker on the inside of the cabinet. A picture would help if you can figure out how to post! I use photobucket to copy an img. format and just paste it in to your post.
Good luck. Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 1942 radio - by Shirley - 11-21-2013, 11:43 AM
RE: Philco 1942 radio - by jerryhawthorne - 11-21-2013, 06:13 PM
RE: Philco 1942 radio - by klondike98 - 11-21-2013, 07:00 PM
RE: Philco 1942 radio - by PhilcoJohn - 11-21-2013, 07:05 PM
RE: Philco 1942 radio - by Ron Ramirez - 11-21-2013, 09:45 PM
RE: Philco 1942 radio - by Arran - 11-21-2013, 10:38 PM
RE: Philco 1942 radio - by vinzer - 11-22-2013, 02:32 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 5013 online users. [Complete List]
» 1 Member(s) | 5012 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios