Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 90 performance.
#10

I have a 90 lowboy and it is a very good performer. Great sensitivity and selectivity.

The AVC action is excellent due to the use of the sharp cutoff 24A tubes in the RF and IF stages. Almost every station comes in at the same volume whether strong or weak, but the sharp cutoff tubes do sometimes cause cross modulation with very strong signals.

The only drawback of the 47 output when compared to a 42 or 6F6 is the low level speaker hum caused by the directly heated AC filament.


Messages In This Thread
Philco 90 performance. - by Jayce - 11-19-2013, 06:18 PM
RE: Philco 90 performance. - by Ron Ramirez - 11-19-2013, 06:34 PM
RE: Philco 90 performance. - by Bill Kinghorn - 11-19-2013, 07:06 PM
RE: Philco 90 performance. - by raydog - 11-19-2013, 07:06 PM
RE: Philco 90 performance. - by Jayce - 11-19-2013, 08:19 PM
RE: Philco 90 performance. - by Jayce - 11-22-2013, 03:30 PM
RE: Philco 90 performance. - by Chuck Schwark - 11-22-2013, 04:03 PM
RE: Philco 90 performance. - by Jayce - 11-22-2013, 05:47 PM
RE: Philco 90 performance. - by Arran - 11-23-2013, 03:32 AM
RE: Philco 90 performance. - by Mondial - 11-23-2013, 09:56 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>