Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

PHILCO 38-15 Mod notes?
#17

Take a look at this schematic:

http://www.nostalgiaair.org/PagesByModel...013233.pdf

It appears that the AVC circuit of this 38-10 model is wired the same way as what you now have (with 6Q7G instead of the 75, but same function). You can see the two 1 Meg resistors connected to the diode plate, with the mica cap connected to the IF coil.

The 250K triode plate load resistor should really not make any difference in operation.

Check the operation of the AVC, because if you remove the 1 Meg resistors, you may disable the AVC function.

Let us know what you find.


Messages In This Thread
PHILCO 38-15 Mod notes? - by Bradley Rush - 11-29-2013, 10:39 PM
RE: PHILCO 38-15 Mod notes? - by Radioroslyn - 11-30-2013, 06:54 PM
RE: PHILCO 38-15 Mod notes? - by Joe Rossi - 11-30-2013, 08:20 PM
RE: PHILCO 38-15 Mod notes? - by Bradley Rush - 11-30-2013, 09:31 PM
RE: PHILCO 38-15 Mod notes? - by Arran - 12-01-2013, 02:31 AM
RE: PHILCO 38-15 Mod notes? - by Bradley Rush - 12-01-2013, 03:09 PM
RE: PHILCO 38-15 Mod notes? - by vinzer - 12-01-2013, 03:23 PM
RE: PHILCO 38-15 Mod notes? - by vinzer - 12-01-2013, 03:33 PM
RE: PHILCO 38-15 Mod notes? - by Bradley Rush - 12-01-2013, 04:42 PM
RE: PHILCO 38-15 Mod notes? - by vinzer - 12-01-2013, 06:19 PM
RE: PHILCO 38-15 Mod notes? - by Bradley Rush - 12-01-2013, 06:25 PM
RE: PHILCO 38-15 Mod notes? - by vinzer - 12-01-2013, 06:44 PM
RE: PHILCO 38-15 Mod notes? - by Radioroslyn - 12-01-2013, 07:07 PM
RE: PHILCO 38-15 Mod notes? - by Mondial - 12-01-2013, 07:31 PM
RE: PHILCO 38-15 Mod notes? - by Arran - 12-02-2013, 12:16 AM
RE: PHILCO 38-15 Mod notes? - by Bradley Rush - 12-02-2013, 04:07 AM
RE: PHILCO 38-15 Mod notes? - by Mondial - 12-02-2013, 08:54 AM
RE: PHILCO 38-15 Mod notes? - by Bradley Rush - 12-07-2013, 01:39 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM

[-]
Who's Online
There are currently 6057 online users. [Complete List]
» 3 Member(s) | 6054 Guest(s)
AvatarAvatarAvatar

>