Philco 37-10

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 37-10

charrday
Junior Member

Posts: 3
Threads: 1
Joined: Dec 2013
City: Richmond State, Province, Country: VA

12-08-2013, 09:52 PM

In restoring a Philco 37-10 I find that the 6H6G discriminator tube is not wired as shown on the schematic. The connections to the plates and cathodes are reversed; my set has the plates going to 2 meg resistors 60 and 61, and the cathodes going to coil 48. The schematic shows it the other way around. Is this a drawing error, or a modification? I hope someone can shed some light on this. I just today got the radio to playing (it seems to play well), and have not yet reassembled the Magnetic Tuning apparatus (I need a new dial from Mark Oppat.) Thanks for any help. Charrday

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 37-10 - by charrday - 12-08-2013, 09:52 PM

RE: Philco 37-10 - by ipwizard - 12-08-2013, 11:44 PM

RE: Philco 37-10 - by Bradley Rush - 12-14-2013, 06:00 PM

RE: Philco 37-10 - by klondike98 - 12-14-2013, 06:22 PM

RE: Philco 37-10 - by Ron Ramirez - 12-14-2013, 07:55 PM

RE: Philco 37-10 - by klondike98 - 12-14-2013, 08:03 PM

RE: Philco 37-10 - by Radioroslyn - 12-15-2013, 11:48 AM

RE: Philco 37-10 - by charrday - 12-26-2013, 04:43 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 3975 online users. [Complete List]
» 4 Member(s) | 3971 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me