Philco 40-190 resistor

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 40-190 resistor

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

#17

12-09-2013, 06:38 PM

Hi Brenda,
I think you must be right.
The electrolitics look fairly old as well.
I either have to figure out how to reverse engineer it, or look for a usable chassis.
Thanks for the input.
murf

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 40-190 resistor - by murf - 12-07-2013, 03:49 PM

RE: Philco 40-190 resistor - by Warren - 12-07-2013, 11:34 PM

RE: Philco 40-190 resistor - by murf - 12-08-2013, 12:28 AM

RE: Philco 40-190 resistor - by DeckApe - 12-08-2013, 10:08 AM

RE: Philco 40-190 resistor - by DeckApe - 12-08-2013, 11:47 AM

RE: Philco 40-190 resistor - by Mondial - 12-08-2013, 12:01 PM

RE: Philco 40-190 resistor - by murf - 12-08-2013, 01:03 PM

RE: Philco 40-190 resistor - by DeckApe - 12-08-2013, 04:13 PM

RE: Philco 40-190 resistor - by murf - 12-08-2013, 04:32 PM

RE: Philco 40-190 resistor - by DeckApe - 12-08-2013, 04:52 PM

RE: Philco 40-190 resistor - by murf - 12-08-2013, 05:12 PM

RE: Philco 40-190 resistor - by 37silverstreak - 12-08-2013, 06:52 PM

RE: Philco 40-190 resistor - by murf - 12-08-2013, 09:19 PM

RE: Philco 40-190 resistor - by Mondial - 12-08-2013, 09:33 PM

RE: Philco 40-190 resistor - by BrendaAnnD - 12-08-2013, 11:02 PM

RE: Philco 40-190 resistor - by BrendaAnnD - 12-08-2013, 11:03 PM

RE: Philco 40-190 resistor - by murf - 12-09-2013, 06:38 PM

RE: Philco 40-190 resistor - by 37silverstreak - 12-09-2013, 08:24 PM

RE: Philco 40-190 resistor - by DeckApe - 12-09-2013, 09:13 PM

RE: Philco 40-190 resistor - by murf - 12-09-2013, 09:38 PM

RE: Philco 40-190 resistor - by 37silverstreak - 12-09-2013, 11:26 PM

RE: Philco 40-190 resistor - by murf - 12-17-2013, 11:35 PM

RE: Philco 40-190 resistor - by Mondial - 12-18-2013, 12:03 AM

RE: Philco 40-190 resistor - by murf - 12-18-2013, 07:55 AM

RE: Philco 40-190 resistor - by murf - 12-21-2013, 05:48 PM

RE: Philco 40-190 resistor - by morzh - 12-21-2013, 07:58 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online

There are currently 5229 online users. [Complete List]
» 2 Member(s) | 5227 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me