47-1230 Refinishing

Thread Rating:

1 Vote(s) - 3 Average
1
2
3
4
5

Linear Mode

47-1230 Refinishing

Warren
Senior Member

Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California

#22

12-13-2013, 07:31 PM

Hi everyone, I have been puting on a few coats of clear laquer on my cabinet. I am trying to get it smooth before I spray any laquer with toner in it. When the laquer dries it isnt exactly smooth, it is kind of bumpy, not vey much and you can use 0000 steel wool to smooth it out fairly easy but i was wondering if this is normal. Should the laquer be pretty smooth overall after it dries? Maybe I need to thin it out more to make a smoother finish? What do you think? I dont have alot of experience at spraying with a compressor/spray gun. Any help will be appreciated. Thanks, Warren

Find

« Next Oldest | Next Newest »

Messages In This Thread

47-1230 Refinishing - by Warren - 06-22-2013, 11:36 PM

RE: 47-1230 Refinishing - by klondike98 - 06-23-2013, 10:45 AM

RE: 47-1230 Refinishing - by Arran - 06-23-2013, 09:08 PM

RE: 47-1230 Refinishing - by Warren - 06-24-2013, 12:49 PM

RE: 47-1230 Refinishing - by Marsupial - 06-27-2013, 03:07 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 06-27-2013, 11:44 PM

RE: 47-1230 Refinishing - by Arran - 06-28-2013, 02:17 AM

RE: 47-1230 Refinishing - by Warren - 06-28-2013, 02:27 PM

RE: 47-1230 Refinishing - by Steve Davis - 06-28-2013, 03:43 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 06-28-2013, 05:02 PM

RE: 47-1230 Refinishing - by Warren - 06-28-2013, 09:07 PM

RE: 47-1230 Refinishing - by Warren - 07-18-2013, 02:26 PM

RE: 47-1230 Refinishing - by Bob Andersen - 07-18-2013, 05:20 PM

RE: 47-1230 Refinishing - by Warren - 07-18-2013, 08:44 PM

RE: 47-1230 Refinishing - by Warren - 07-30-2013, 12:55 AM

RE: 47-1230 Refinishing - by Arran - 07-30-2013, 10:39 AM

RE: 47-1230 Refinishing - by jerryhawthorne - 07-30-2013, 01:47 PM

RE: 47-1230 Refinishing - by Warren - 07-31-2013, 12:01 AM

RE: 47-1230 Refinishing - by jerryhawthorne - 07-31-2013, 12:11 AM

RE: 47-1230 Refinishing - by Warren - 08-03-2013, 11:45 PM

RE: 47-1230 Refinishing - by Warren - 10-13-2013, 10:58 PM

RE: 47-1230 Refinishing - by Warren - 12-13-2013, 07:31 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 12-13-2013, 08:00 PM

RE: 47-1230 Refinishing - by Warren - 12-14-2013, 04:16 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 12-14-2013, 05:22 PM

RE: 47-1230 Refinishing - by Warren - 12-15-2013, 02:17 AM

View a Printable Version

Users browsing this thread: 10 Guest(s)

Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me