47-1230 Refinishing

Thread Rating:

1 Vote(s) - 3 Average
1
2
3
4
5

Linear Mode

47-1230 Refinishing

Warren
Senior Member

Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California

#24

12-14-2013, 04:16 PM

Ok, it sounds like I have it a little thick then. I am useing an hvlp gun also with max 40 psi. I have about 30 psi going through it. I will try a 50/50 mix. Was a little cautious about using so much thinner as the directions on the can says not to use that much thinner but I will try what you say. Im useing Deft brushing Laquer, but earlier you said that was ok. Thanks, 50/50 mix next time. Will let you know soon how it works out.

Find

« Next Oldest | Next Newest »

Messages In This Thread

47-1230 Refinishing - by Warren - 06-22-2013, 11:36 PM

RE: 47-1230 Refinishing - by klondike98 - 06-23-2013, 10:45 AM

RE: 47-1230 Refinishing - by Arran - 06-23-2013, 09:08 PM

RE: 47-1230 Refinishing - by Warren - 06-24-2013, 12:49 PM

RE: 47-1230 Refinishing - by Marsupial - 06-27-2013, 03:07 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 06-27-2013, 11:44 PM

RE: 47-1230 Refinishing - by Arran - 06-28-2013, 02:17 AM

RE: 47-1230 Refinishing - by Warren - 06-28-2013, 02:27 PM

RE: 47-1230 Refinishing - by Steve Davis - 06-28-2013, 03:43 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 06-28-2013, 05:02 PM

RE: 47-1230 Refinishing - by Warren - 06-28-2013, 09:07 PM

RE: 47-1230 Refinishing - by Warren - 07-18-2013, 02:26 PM

RE: 47-1230 Refinishing - by Bob Andersen - 07-18-2013, 05:20 PM

RE: 47-1230 Refinishing - by Warren - 07-18-2013, 08:44 PM

RE: 47-1230 Refinishing - by Warren - 07-30-2013, 12:55 AM

RE: 47-1230 Refinishing - by Arran - 07-30-2013, 10:39 AM

RE: 47-1230 Refinishing - by jerryhawthorne - 07-30-2013, 01:47 PM

RE: 47-1230 Refinishing - by Warren - 07-31-2013, 12:01 AM

RE: 47-1230 Refinishing - by jerryhawthorne - 07-31-2013, 12:11 AM

RE: 47-1230 Refinishing - by Warren - 08-03-2013, 11:45 PM

RE: 47-1230 Refinishing - by Warren - 10-13-2013, 10:58 PM

RE: 47-1230 Refinishing - by Warren - 12-13-2013, 07:31 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 12-13-2013, 08:00 PM

RE: 47-1230 Refinishing - by Warren - 12-14-2013, 04:16 PM

RE: 47-1230 Refinishing - by jerryhawthorne - 12-14-2013, 05:22 PM

RE: 47-1230 Refinishing - by Warren - 12-15-2013, 02:17 AM

View a Printable Version

Users browsing this thread: 8 Guest(s)

Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me